Convert CONFIG_MCFUART to Kconfig

[platform/kernel/u-boot.git] / include / configs / astro_mcf5373l.h

diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index 7eec226..36e351f 100644 (file)
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -22,23 +22,22 @@
  * set the card type to actually compile for; either of
  * the possibilities listed below has to be used!
  */
-#define CONFIG_ASTRO_V532      1
+#define ASTRO_V532     1
 
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define ASTRO_ID       0xF8
-#elif CONFIG_ASTRO_V512
+#elif ASTRO_V512
 #define ASTRO_ID       0xFA
-#elif CONFIG_ASTRO_TWIN7S2
+#elif ASTRO_TWIN7S2
 #define ASTRO_ID       0xF9
-#elif CONFIG_ASTRO_V912
+#elif ASTRO_V912
 #define ASTRO_ID       0xFC
-#elif CONFIG_ASTRO_COFDMDUOS2
+#elif ASTRO_COFDMDUOS2
 #define ASTRO_ID       0xFB
 #else
 #error No card type defined!
 #endif
 
-/* Command line configuration */
 /*
  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  * a different bootloader that has already performed RAM setup) or
@@ -59,11 +58,6 @@
 #define CONFIG_MCFTMR
 
 /* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED       80000
-#define CONFIG_SYS_FSL_I2C_SLAVE       0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET      0x58000
 #define CONFIG_SYS_IMMR                        CONFIG_SYS_MBAR
 
 /*
@@ -87,7 +81,6 @@
  * in u-boot command interface
  */
 
-#define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT           (2)
 #define CONFIG_SYS_UART2_ALT3_GPIO
 
@@ -150,7 +143,7 @@
 #ifdef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_BOOTCOMMAND     ""      /* no autoboot in this case */
 #else
-#if CONFIG_ASTRO_V532
+#if ASTRO_V532
 #define CONFIG_BOOTCOMMAND     "protect off 0x80000 0x1ffffff;run env_check;"\
                                "run xilinxload&&run alteraload&&bootm 0x80000;"\
                                "update;reset"
@@ -160,9 +153,6 @@
 #endif
 #endif
 
-/* default RAM address for user programs */
-#define CONFIG_SYS_LOAD_ADDR   0x20000
-
 #define CONFIG_FPGA_COUNT      1
 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 #define CONFIG_SYS_FPGA_WAIT           1000
@@ -241,8 +231,6 @@
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)
 
 #define CONFIG_SYS_BOOTPARAMS_LEN      (64 * 1024)
-/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_MALLOC_LEN          (128 << 10)
 
 /*
  * For booting Linux, the board info and command line data
@@ -273,7 +261,6 @@
 #endif
 
 /* Cache Configuration */
-#define CONFIG_SYS_CACHELINE_SIZE      16
 
 #define ICACHE_STATUS                  (CONFIG_SYS_INIT_RAM_ADDR + \
                                         CONFIG_SYS_INIT_RAM_SIZE - 8)