#define CONFIG_APOLLON 1
#define CONFIG_APOLLON_PLUS 1 /* If you have apollon plus 1.x */
+#define CONFIG_ONENAND_U_BOOT y
+
/* Clock config to target*/
#define PRCM_CONFIG_I 1
/* #define PRCM_CONFIG_II 1 */
* Size of malloc() pool
*/
#define CONFIG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE_FLEX SZ_256K
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_1M)
-/* bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
/*
* Hardware drivers
/*
* SMC91c96 Etherent
*/
-#define CONFIG_DRIVER_LAN91C96
+#define CONFIG_LAN91C96
#define CONFIG_LAN91C96_BASE (APOLLON_CS1_BASE+0x300)
#define CONFIG_LAN91C96_EXT_PHY
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <config_cmd_default.h>
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS
#endif
-#undef CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_SOURCE
#ifndef CONFIG_SYS_USE_NOR
# undef CONFIG_CMD_FLASH
/*
* Miscellaneous configurable options
*/
-#define V_PROMPT "Apollon # "
-
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT V_PROMPT
+#define CONFIG_SYS_PROMPT "Apollon # "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MEMTEST_START (OMAP2420_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M)
-#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
/* default load address */
#define CONFIG_SYS_LOAD_ADDR (OMAP2420_SDRC_CS0)
* or by 32KHz clk, or from external sig. This rate is divided by a local
* divisor.
*/
-#define V_PVT 7 /* use with 12MHz/128 */
-
#define CONFIG_SYS_TIMERBASE OMAP2420_GPT2
-#define CONFIG_SYS_PVT V_PVT /* 2^(pvt+1) */
-#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PVT))
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
+#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
/*-----------------------------------------------------------------------
* Stack sizes
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE SZ_128K /* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
-#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
/* OneNAND boot, OneNAND has CS0, NOR boot ONeNAND has CS2 */
#define CONFIG_SYS_ONENAND_BASE 0x00000000
+#define CONFIG_SYS_MONITOR_LEN SZ_256K /* U-Boot image size */
#define CONFIG_ENV_IS_IN_ONENAND 1
#define CONFIG_ENV_ADDR 0x00020000
+#define CONFIG_ENV_ADDR_FLEX 0x00040000
#ifdef CONFIG_SYS_USE_UBI
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "onenand0=onenand"
#define MTDPARTS_DEFAULT "mtdparts=onenand:128k(bootloader)," \
"128k(params)," \
"-(ubifs)"
#endif
+#define PHYS_SRAM 0x4020F800
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM
+
#endif /* __CONFIG_H */