#define __CONFIG_AM654_EVM_H
#include <linux/sizes.h>
-#include <config_distro_bootcmd.h>
#include <environment/ti/mmc.h>
#include <environment/ti/k3_rproc.h>
#include <environment/ti/k3_dfu.h>
/* DDR Configuration */
#define CONFIG_SYS_SDRAM_BASE1 0x880000000
-/* SPL Loader Configuration */
-#ifdef CONFIG_TARGET_AM654_A53_EVM
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
- CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
-#define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x20000
-#else
-/*
- * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
- * possible (to allow the build to go through), as this directly affects
- * our memory footprint. The less we use for BSS the more we have available
- * for everything else.
- */
-#define CONFIG_SPL_BSS_MAX_SIZE 0xc00
-/*
- * Link BSS to be within SPL in a dedicated region located near the top of
- * the MCU SRAM, this way making it available also before relocation. Note
- * that we are not using the actual top of the MCU SRAM as there is a memory
- * location filled in by the boot ROM that we want to read out without any
- * interference from the C context.
- */
-#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
- CONFIG_SPL_BSS_MAX_SIZE)
-/* Set the stack right below the SPL BSS section */
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
-/* Configure R5 SPL post-relocation malloc pool in DDR */
-#define CONFIG_SYS_SPL_MALLOC_START 0x84000000
-#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
-#define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x5000
-#endif
-
-#ifdef CONFIG_SYS_K3_SPL_ATF
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
-#endif
-
-#ifndef CONFIG_CPU_V7R
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-
-/*
- * If the maximum size is not declared then it is defined as
- * CONFIG_SYS_DFU_DATA_BUF_SIZE.
- */
-#define CONFIG_SYS_DFU_MAX_FILE_SIZE (1024 * 1024 * 8) /* 8 MiB */
-
-#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
-
-#define CONFIG_SYS_BOOTM_LEN SZ_64M
-
#define PARTS_DEFAULT \
/* Linux partitions */ \
"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
"0 /lib/firmware/am65x-mcu-r5f0_0-fw " \
"1 /lib/firmware/am65x-mcu-r5f0_1-fw "
-#ifdef CONFIG_TARGET_AM654_A53_EVM
-#define EXTRA_ENV_AM65X_BOARD_SETTINGS_MTD \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
-#else
-#define EXTRA_ENV_AM65X_BOARD_SETTINGS_MTD
-#endif
-
#define EXTRA_ENV_AM65X_BOARD_SETTINGS_UBI \
"init_ubi=run args_all args_ubi; sf probe; " \
"ubi part ospi.rootfs; ubifsmount ubi:rootfs;\0" \
DFU_ALT_INFO_EMMC \
DFU_ALT_INFO_OSPI
+#ifdef CONFIG_TARGET_AM654_A53_EVM
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 1) \
+ func(MMC, mmc, 0)
+
+#include <config_distro_bootcmd.h>
+#else
+#define BOOTENV
+#endif
+
/* Incorporate settings into the U-Boot environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_FIT_TI_ARGS \
EXTRA_ENV_AM65X_BOARD_SETTINGS \
EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC \
- EXTRA_ENV_AM65X_BOARD_SETTINGS_MTD \
EXTRA_ENV_AM65X_BOARD_SETTINGS_UBI \
EXTRA_ENV_RPROC_SETTINGS \
- EXTRA_ENV_DFUARGS
-
-#define CONFIG_SYS_USB_FAT_BOOT_PARTITION 1
+ EXTRA_ENV_DFUARGS \
+ BOOTENV
/* Now for the remaining common defines */
#include <configs/ti_armv7_common.h>