#include <configs/ti_omap3_common.h>
-/* Ethernet */
-#define CONFIG_NET_RETRY_COUNT 10
-
/* Board NAND Info. */
#ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
11, 12, 13, 14, 16, 17, 18, 19, 20, \
21, 22, 23, 24, 25, 26, 27, 28, 30, \
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
/* NAND block size is 128 KiB. Synchronize these values with
* corresponding Device Tree entries in Linux:
#endif /* CONFIG_MTD_RAW_NAND */
/* Environment information */
-
-#define CONFIG_BOOTFILE "uImage"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
"nand read ${fdtaddr} aa0000 80000; " \
"bootm ${loadaddr} - ${fdtaddr}\0" \
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "echo SD/MMC found on device $mmcdev; " \
- "if run loadbootenv; then " \
- "run importbootenv; " \
- "fi; " \
- "echo Checking if uenvcmd is set ...; " \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...; " \
- "run uenvcmd; " \
- "fi; " \
- "echo Running default loadimage ...; " \
- "setenv bootfile zImage; " \
- "if run loadimage; then " \
- "run loadfdt; " \
- "run mmcboot; " \
- "fi; " \
- "else run nandboot; fi"
-
/* Miscellaneous configurable options */
/* We set the max number of command args high to avoid HUSH bugs. */
/* **** PISMO SUPPORT *** */
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
/* on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#if defined(CONFIG_MTD_RAW_NAND)