#include <configs/ti_am335x_common.h>
#include <linux/sizes.h>
-#ifndef CONFIG_SPL_BUILD
-# define CONFIG_TIMESTAMP
-#endif
-
#define CONFIG_SYS_BOOTM_LEN SZ_16M
-#define CONFIG_MACH_TYPE MACH_TYPE_AM335XEVM
-
/* Clock Defines */
#define V_OSCK 24000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK)
-#ifdef CONFIG_NAND
+#ifdef CONFIG_MTD_RAW_NAND
#define NANDARGS \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
#define NANDARGS ""
#endif
-#define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
- "bootcmd_" #devtypel #instance "=" \
- "setenv mmcdev " #instance"; "\
- "setenv bootpart " #instance":2 ; "\
- "run mmcboot\0"
-
-#define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
- #devtypel #instance " "
-
#define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
"bootcmd_" #devtypel "=" \
"run nandboot\0"
#define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
#devtypel #instance " "
+#if CONFIG_IS_ENABLED(CMD_USB)
+# define BOOT_TARGET_USB(func) func(USB, usb, 0)
+#else
+# define BOOT_TARGET_USB(func)
+#endif
+
#if CONFIG_IS_ENABLED(CMD_PXE)
# define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
#else
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
- func(LEGACY_MMC, legacy_mmc, 0) \
func(MMC, mmc, 1) \
- func(LEGACY_MMC, legacy_mmc, 1) \
func(NAND, nand, 0) \
+ BOOT_TARGET_USB(func) \
BOOT_TARGET_PXE(func) \
BOOT_TARGET_DHCP(func)
#ifndef CONFIG_SPL_BUILD
#include <environment/ti/dfu.h>
-#include <environment/ti/mmc.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
- DEFAULT_MMC_TI_ARGS \
- DEFAULT_FIT_TI_ARGS \
- "bootpart=0:2\0" \
- "bootdir=/boot\0" \
- "bootfile=zImage\0" \
"fdtfile=undefined\0" \
+ "finduuid=part uuid mmc 0:2 uuid\0" \
"console=ttyO0,115200n8\0" \
"partitions=" \
"uuid_disk=${uuid_gpt_disk};" \
"if test $board_name = A335X_SK; then " \
"setenv fdtfile am335x-evmsk.dtb; fi; " \
"if test $board_name = A335_ICE; then " \
- "setenv fdtfile am335x-icev2.dtb; fi; " \
+ "setenv fdtfile am335x-icev2.dtb; " \
+ "if test $ice_mii = mii; then " \
+ "setenv pxe_label_override Pruss; fi;" \
+ "fi; " \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine device tree to use; fi; \0" \
"init_console=" \
#define CONFIG_SYS_NS16550_COM5 0x481a8000 /* UART4 */
#define CONFIG_SYS_NS16550_COM6 0x481aa000 /* UART5 */
-#define CONFIG_ENV_EEPROM_IS_ON_I2C
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
/* PMIC support */
#define CONFIG_POWER_TPS65217
#define CONFIG_POWER_TPS65910
/* USB gadget RNDIS */
#endif
-#ifdef CONFIG_NAND
+#ifdef CONFIG_MTD_RAW_NAND
/* NAND: device related configs */
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
- CONFIG_SYS_NAND_PAGE_SIZE)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
/* NAND: driver related configs */
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
10, 11, 12, 13, 14, 15, 16, 17, \
18, 19, 20, 21, 22, 23, 24, 25, \
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x000c0000
/* NAND: SPL related configs */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000 /* kernel offset */
#endif
-#endif /* !CONFIG_NAND */
+#endif /* !CONFIG_MTD_RAW_NAND */
/*
* For NOR boot, we must set this to the start of where NOR is mapped
*/
/*
- * USB configuration. We enable MUSB support, both for host and for
- * gadget. We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each. Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
-/*
* Disable MMC DM for SPL build and can be re-enabled after adding
* DM support in SPL
*/
#if defined(CONFIG_SPI_BOOT)
/* SPL related */
#elif defined(CONFIG_EMMC_BOOT)
-#define CONFIG_SYS_MMC_ENV_DEV 1
-#define CONFIG_SYS_MMC_ENV_PART 0
#define CONFIG_SYS_MMC_MAX_DEVICE 2
-#elif defined(CONFIG_ENV_IS_IN_NAND)
-#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#endif
-/* SPI flash. */
-
/* Network. */
-#define CONFIG_PHY_SMSC
/* Enable Atheros phy driver */
-#define CONFIG_PHY_ATHEROS
/*
* NOR Size = 16 MiB
*/
#if defined(CONFIG_NOR)
#define CONFIG_SYS_MAX_FLASH_SECT 128
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_FLASH_BASE (0x08000000)
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_SIZE 0x01000000