Convert CONFIG_SYS_BOOTM_LEN to Kconfig
[platform/kernel/u-boot.git] / include / configs / am335x_evm.h
index 0f34080..4b59759 100644 (file)
 #include <configs/ti_am335x_common.h>
 #include <linux/sizes.h>
 
-#ifndef CONFIG_SPL_BUILD
-# define CONFIG_TIMESTAMP
-#endif
-
-#define CONFIG_SYS_BOOTM_LEN           SZ_16M
-
 /* Clock Defines */
 #define V_OSCK                         24000000  /* Clock output from T2 */
 #define V_SCLK                         (V_OSCK)
 
 #ifdef CONFIG_MTD_RAW_NAND
 #define NANDARGS \
-       "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
-       "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
        "nandargs=setenv bootargs console=${console} " \
                "${optargs} " \
                "root=${nandroot} " \
                "rootfstype=${nandrootfstype}\0" \
        "nandroot=ubi0:rootfs rw ubi.mtd=NAND.file-system,2048\0" \
-       "nandrootfstype=ubifs rootwait=1\0" \
+       "nandrootfstype=ubifs rootwait\0" \
        "nandboot=echo Booting from nand ...; " \
                "run nandargs; " \
                "nand read ${fdtaddr} NAND.u-boot-spl-os; " \
                        "setenv fdtfile am335x-boneblue.dtb; fi; " \
                "if test $board_name = BBEN; then " \
                        "setenv fdtfile am335x-sancloud-bbe.dtb; fi; " \
+               "if test $board_name = BBELITE; then " \
+                       "setenv fdtfile am335x-sancloud-bbe-lite.dtb; fi; " \
+               "if test $board_name = BBE_EX_WIFI; then " \
+                       "setenv fdtfile am335x-sancloud-bbe-extended-wifi.dtb; fi; " \
                "if test $board_name = A33515BB; then " \
                        "setenv fdtfile am335x-evm.dtb; fi; " \
                "if test $board_name = A335X_SK; then " \
 #define CONFIG_SYS_NS16550_COM6                0x481aa000      /* UART5 */
 
 /* PMIC support */
-#define CONFIG_POWER_TPS65217
 #define CONFIG_POWER_TPS65910
 
-/* SPL */
-#ifndef CONFIG_NOR_BOOT
-/* Bootcount using the RTC block */
-#define CONFIG_SYS_BOOTCOUNT_BE
-
-/* USB gadget RNDIS */
-#endif
-
 #ifdef CONFIG_MTD_RAW_NAND
 /* NAND: device related configs */
 /* NAND: driver related configs */
 
 #define CONFIG_SYS_NAND_ECCSIZE                512
 #define CONFIG_SYS_NAND_ECCBYTES       14
-/* NAND: SPL related configs */
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS        0x00200000 /* kernel offset */
-#endif
 #endif /* !CONFIG_MTD_RAW_NAND */
 
-/*
- * For NOR boot, we must set this to the start of where NOR is mapped
- * in memory.
- */
-
-/*
- * USB configuration.  We enable MUSB support, both for host and for
- * gadget.  We set USB0 as peripheral and USB1 as host, based on the
- * board schematic and physical port wired to each.  Then for host we
- * add mass storage support and for gadget we add both RNDIS ethernet
- * and DFU.
- */
-#define CONFIG_AM335X_USB0
-#define CONFIG_AM335X_USB0_MODE        MUSB_PERIPHERAL
-#define CONFIG_AM335X_USB1
-#define CONFIG_AM335X_USB1_MODE MUSB_HOST
-
-/*
- * Disable MMC DM for SPL build and can be re-enabled after adding
- * DM support in SPL
- */
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_DM_MMC
-#undef CONFIG_TIMER
-#endif
-
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USB_ETHER)
-/* Remove other SPL modes. */
-/* disable host part of MUSB in SPL */
-/* disable EFI partitions and partition UUID support */
-#endif
-
 /* USB Device Firmware Update support */
 #ifndef CONFIG_SPL_BUILD
 #define DFUARGS \
  */
 #if defined(CONFIG_NOR)
 #define CONFIG_SYS_MAX_FLASH_SECT      128
-#define CONFIG_SYS_MAX_FLASH_BANKS     1
 #define CONFIG_SYS_FLASH_BASE          (0x08000000)
-#define CONFIG_SYS_FLASH_CFI_WIDTH     FLASH_CFI_16BIT
 #define CONFIG_SYS_FLASH_SIZE          0x01000000
-#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 #endif  /* NOR support */
 
-#ifdef CONFIG_DRIVER_TI_CPSW
-#define CONFIG_CLOCK_SYNTHESIZER
-#define CLK_SYNTHESIZER_I2C_ADDR 0x65
-#endif
-
 #endif /* ! __CONFIG_AM335X_EVM_H */