/*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
*----------------------------------------------------------------------*/
#define CONFIG_ALPR 1 /* Board is ebony */
#define CONFIG_440GX 1 /* Specifc GX support */
+#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
+#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */
-#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
-#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */
+#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */
+#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
+#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
+#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
+#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000)
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-
-#if 0 /* test-only */
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */
-#endif
-
-/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
-
+#define CFG_FLASH_CFI 1 /* The flash is CFI compatible */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
-
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*-----------------------------------------------------------------------
* DDR SDRAM
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \"run kernelx\" to boot the system;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
+ "netdev=eth3\0" \
"hostname=alpr\0" \
+ "fdt_file=alpr/alpr.dtb\0" \
+ "fdt_addr=400000\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
+ "nfsroot=${serverip}:${rootpath} ${init}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \
+ "mem=193M\0" \
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/alpr/uImage\0" \
+ "net_nfs_fdt=tftp 200000 ${bootfile};" \
+ "tftp ${fdt_addr} ${fdt_file};" \
+ "run nfsargs addip addtty;" \
+ "bootm 200000 - ${fdt_addr}\0" \
+ "rootpath=/opt/projects/alpr/nfs_root\0" \
+ "bootfile=/alpr/uImage\0" \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "load=tftp 100000 /tftpboot/alpr/u-boot.bin\0" \
+ "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \
"setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
+ "ethprime=ppc_4xx_eth3\0" \
+ "ethact=ppc_4xx_eth3\0" \
+ "autoload=no\0" \
+ "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \
+ "load_fpga=fpga load 0 ffe00000 10dd9a\0" \
+ "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \
+ "rootfstype=jffs2 init=/sbin/init\0" \
+ "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\
+ ";bootm 200000\0" \
+ "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \
+ "addtty;bootm 200000\0" \
+ "kernel1=setenv actkernel 'kernel1';run load_fpga " \
+ "kernel1_mtd\0" \
+ "kernel2=setenv actkernel 'kernel2';run load_fpga " \
+ "kernel2_mtd\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND "run kernel2"
+
+#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */
#define CONFIG_BAUDRATE 115200
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */
#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */
-#define CONFIG_PHY2_ADDR 0x00 /* test-only: will be changed */
-#define CONFIG_PHY3_ADDR 0x01 /* PHY address for EMAC3 */
+#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */
+#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-#define CONFIG_88E1111_CLK_DELAY 1 /* set CLK delay on ALPR */
+#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-#if 0 /* test-only */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SNTP )
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_FPGA | \
- CFG_CMD_NAND | \
- CFG_CMD_REGINFO)
-#endif
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_ALT_MEMTEST 1 /* Enable more extensive memtest*/
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
/*-----------------------------------------------------------------------
* PCI stuff
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT /* let board init pci target */
#define CFG_PCI_MASTER_INIT
/*-----------------------------------------------------------------------
* FPGA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_FPGA CFG_ALTERA_CYCLON2
-#undef CFG_FPGA_CHECK_CTRLC
-#undef CFG_FPGA_PROG_FEEDBACK
+ *-----------------------------------------------------------------------*/
+#define CONFIG_FPGA
+#define CONFIG_FPGA_ALTERA
+#define CONFIG_FPGA_CYCLON2
+#define CFG_FPGA_CHECK_CTRLC
+#define CFG_FPGA_PROG_FEEDBACK
#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in
Reihe geschaltet -> sollte gehen,
aufpassen mit Datasize ist jetzt
ist das mit den multiple Device in PS
Mode erklaert ...*/
-
/* FPGA program pin configuration */
#define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */
#define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */
#define CFG_GPIO_SEL_AVR 15 /* cpu output */
#define CFG_GPIO_PROG_EN 23 /* cpu output */
-/*
- * NAND-FLASH stuff
- */
-#define CFG_MAX_NAND_DEVICE 2
-#define NAND_MAX_CHIPS 2
-#define CFG_NAND_BASE 0x50000000 /* NAND FLASH Base Address */
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup
+ *-----------------------------------------------------------------------*/
+#define CFG_GPIO_SHUTDOWN (0x80000000 >> 6)
+#define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9)
+#define CFG_GPIO_EREADY (0x80000000 >> 26)
+#define CFG_GPIO_REV0 (0x80000000 >> 14)
+#define CFG_GPIO_REV1 (0x80000000 >> 15)
-#if 0
-#define CONFIG_MTD_DEBUG
-#define CONFIG_MTD_DEBUG_VERBOSE 4
-#endif
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE 4
+#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE
+#define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */
+#define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \
+ CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 }
+#define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
#define CFG_EBC_PB0AP 0x92015480
#define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */
-/* Memory Bank 1 (NAND-FLASH) initialization */
-/*#define CFG_EBC_PB1AP 0x108f4380 */ /* TODO */
-/*#define CFG_EBC_PB1AP 0x7f854380 */ /* TODO */
-/*#define CFG_EBC_PB1AP 0x108553c0 */
-/*#define CFG_EBC_PB1AP 0x108053c0 */
-#define CFG_EBC_PB1AP 0x10810180
-/*#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) *//* BS=1MB,BU=R/W,BW=8bit */
-#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x1A000) /* BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (NAND-FLASH) initialization */
+#define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */
+#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */
/*
* For booting Linux, the board info and command line data
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff