net: Move the CMD_NET config to defconfigs

[platform/kernel/u-boot.git] / include / configs / alpr.h

diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index 86b874c..0f125dc 100644 (file)
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -14,7 +14,6 @@
 #define CONFIG_ALPR            1           /* Board is ebony           */
 #define CONFIG_440GX           1           /* Specifc GX support       */
 #define CONFIG_440             1           /* ... PPC440 family        */
-#define CONFIG_4xx             1           /* ... PPC4xx family        */
 #define CONFIG_BOARD_EARLY_INIT_F 1        /* Call board_pre_init      */
 #define CONFIG_LAST_STAGE_INIT 1           /* call last_stage_init()   */
 
@@ -148,7 +147,7 @@
        "flash_self=run ramargs addip addtty;"                          \
                "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
        "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-               "bootm\0"                                               \
+               "bootm\0"                                               \
        "net_nfs_fdt=tftp 200000 ${bootfile};"                          \
                "tftp ${fdt_addr} ${fdt_file};"                         \
                "run nfsargs addip addtty;"                             \
@@ -223,12 +222,12 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
 #define CONFIG_CMD_I2C
 #undef CONFIG_CMD_LOADB
 #undef CONFIG_CMD_LOADS
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
 #undef CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 
@@ -238,7 +237,6 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory         */
-#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt       */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size      */
 #else
@@ -255,8 +253,6 @@
 #define CONFIG_SYS_LOAD_ADDR           0x100000        /* default load address */
 #define CONFIG_SYS_EXTBDINFO           1       /* To use extended board_into (bd_t) */
 
-#define CONFIG_SYS_HZ                  1000    /* decrementer freq: 1 ms ticks */
-
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC       1       /* enable mdc/mwc commands      */
@@ -327,6 +323,8 @@
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2,   \
                                  CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
 #define CONFIG_SYS_NAND_QUIET_TEST     1       /* don't warn upon unknown NAND flash   */
+#define CONFIG_SYS_NAND_MAX_OOBFREE    2
+#define CONFIG_SYS_NAND_MAX_ECCPOS     56
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
@@ -350,7 +348,6 @@
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
 
 /* pass open firmware flat tree */