/*
- * (C) Copyright 2007 DENX Software Engineering
+ * (C) Copyright 2007, 2008 DENX Software Engineering
*
* See file CREDITS for list of people who contributed to this
* project.
#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_ADS5121 1
/*
* Memory map for the ADS5121 board:
*
* 0x3000_0000 - 0x3001_FFFF SRAM (128 KB)
* 0x8000_0000 - 0x803F_FFFF IMMR (4 MB)
* 0x8200_0000 - 0x8200_001F CPLD (32 B)
+ * 0x8400_0000 - 0x82FF_FFFF PCI I/O space (16 MB)
+ * 0xA000_0000 - 0xAFFF_FFFF PCI memory space (256 MB)
+ * 0xB000_0000 - 0xBFFF_FFFF PCI memory mapped I/O space (256 MB)
* 0xFC00_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB)
*/
*/
#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC512X 1 /* MPC512X family */
+#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */
-#undef CONFIG_PCI
+/* video */
+#undef CONFIG_VIDEO
-#define CFG_MPC512X_CLKIN 66000000 /* in Hz */
+#if defined(CONFIG_VIDEO)
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#endif
+
+/* CONFIG_PCI is defined at config time */
+
+#ifdef CONFIG_ADS5121_REV2
+#define CONFIG_SYS_MPC512X_CLKIN 66000000 /* in Hz */
+#else
+#define CONFIG_SYS_MPC512X_CLKIN 33333333 /* in Hz */
+#define CONFIG_PCI
+#endif
#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R
-#define CFG_IMMR 0x80000000
+#define CONFIG_SYS_IMMR 0x80000000
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100)
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* DDR Setup - manually set all parameters as there's no SPD etc.
*/
-#define CFG_DDR_SIZE 256 /* MB */
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_BASE
+#ifdef CONFIG_ADS5121_REV2
+#define CONFIG_SYS_DDR_SIZE 256 /* MB */
+#else
+#define CONFIG_SYS_DDR_SIZE 512 /* MB */
+#endif
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
/* DDR Controller Configuration
*
* [09:05] DRAM tRP:
* [04:00] DRAM tRPA
*/
-
-#define CFG_MDDRC_SYS_CFG 0xF8604A00
-#define CFG_MDDRC_SYS_CFG_RUN 0xE8604A00
-#define CFG_MDDRC_SYS_CFG_EN 0xF0000000
-#define CFG_MDDRC_TIME_CFG0 0x00003D2E
-#define CFG_MDDRC_TIME_CFG0_RUN 0x06183D2E
-#define CFG_MDDRC_TIME_CFG1 0x54EC1168
-#define CFG_MDDRC_TIME_CFG2 0x35210864
-
-#define CFG_MICRON_NOP 0x01380000
-#define CFG_MICRON_PCHG_ALL 0x01100400
-#define CFG_MICRON_EM2 0x01020000
-#define CFG_MICRON_EM3 0x01030000
-#define CFG_MICRON_EN_DLL 0x01010000
-#define CFG_MICRON_RFSH 0x01080000
-#define CFG_MICRON_INIT_DEV_OP 0x01000432
-#define CFG_MICRON_OCD_DEFAULT 0x01010780
+#ifdef CONFIG_ADS5121_REV2
+#define CONFIG_SYS_MDDRC_SYS_CFG 0xF8604A00
+#define CONFIG_SYS_MDDRC_SYS_CFG_RUN 0xE8604A00
+#define CONFIG_SYS_MDDRC_TIME_CFG1 0x54EC1168
+#define CONFIG_SYS_MDDRC_TIME_CFG2 0x35210864
+#else
+#define CONFIG_SYS_MDDRC_SYS_CFG 0xFA804A00
+#define CONFIG_SYS_MDDRC_SYS_CFG_RUN 0xEA804A00
+#define CONFIG_SYS_MDDRC_TIME_CFG1 0x68EC1168
+#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34310864
+#endif
+#define CONFIG_SYS_MDDRC_SYS_CFG_EN 0xF0000000
+#define CONFIG_SYS_MDDRC_TIME_CFG0 0x00003D2E
+#define CONFIG_SYS_MDDRC_TIME_CFG0_RUN 0x06183D2E
+
+#define CONFIG_SYS_MICRON_NOP 0x01380000
+#define CONFIG_SYS_MICRON_PCHG_ALL 0x01100400
+#define CONFIG_SYS_MICRON_EM2 0x01020000
+#define CONFIG_SYS_MICRON_EM3 0x01030000
+#define CONFIG_SYS_MICRON_EN_DLL 0x01010000
+#define CONFIG_SYS_MICRON_RFSH 0x01080000
+#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432
+#define CONFIG_SYS_MICRON_OCD_DEFAULT 0x01010780
/* DDR Priority Manager Configuration */
-#define CFG_MDDRCGRP_PM_CFG1 0x000777AA
-#define CFG_MDDRCGRP_PM_CFG2 0x00000055
-#define CFG_MDDRCGRP_HIPRIO_CFG 0x00000000
-#define CFG_MDDRCGRP_LUT0_MU 0x11111117
-#define CFG_MDDRCGRP_LUT0_ML 0x7777777A
-#define CFG_MDDRCGRP_LUT1_MU 0x4444EEEE
-#define CFG_MDDRCGRP_LUT1_ML 0xEEEEEEEE
-#define CFG_MDDRCGRP_LUT2_MU 0x44444444
-#define CFG_MDDRCGRP_LUT2_ML 0x44444444
-#define CFG_MDDRCGRP_LUT3_MU 0x55555555
-#define CFG_MDDRCGRP_LUT3_ML 0x55555558
-#define CFG_MDDRCGRP_LUT4_MU 0x11111111
-#define CFG_MDDRCGRP_LUT4_ML 0x1111117C
-#define CFG_MDDRCGRP_LUT0_AU 0x33333377
-#define CFG_MDDRCGRP_LUT0_AL 0x7777EEEE
-#define CFG_MDDRCGRP_LUT1_AU 0x11111111
-#define CFG_MDDRCGRP_LUT1_AL 0x11111111
-#define CFG_MDDRCGRP_LUT2_AU 0x11111111
-#define CFG_MDDRCGRP_LUT2_AL 0x11111111
-#define CFG_MDDRCGRP_LUT3_AU 0x11111111
-#define CFG_MDDRCGRP_LUT3_AL 0x11111111
-#define CFG_MDDRCGRP_LUT4_AU 0x11111111
-#define CFG_MDDRCGRP_LUT4_AL 0x11111111
+#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777
+#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000
+#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001
+#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC
+#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA
+#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666
+#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555
+#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444
+#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444
+#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555
+#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558
+#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122
+#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa
+#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa
+#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666
+#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666
+#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111
+#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111
/*
* NOR FLASH on the Local Bus
*/
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CFG_FLASH_BASE 0xFC000000 /* start of FLASH */
-#define CFG_FLASH_SIZE 0x04000000 /* max flash size in bytes */
-#define CFG_FLASH_USE_BUFFER_WRITE
-
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
+#undef CONFIG_BKUP_FLASH
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#ifdef CONFIG_BKUP_FLASH
+#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* max flash size in bytes */
+#else
+#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* max flash size in bytes */
+#endif
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-#undef CFG_FLASH_CHECKSUM
+#undef CONFIG_SYS_FLASH_CHECKSUM
/*
* CPLD registers area is really only 32 bytes in size, but the smallest possible LP
* window is 64KB
*/
-#define CFG_CPLD_BASE 0x82000000
-#define CFG_CPLD_SIZE 0x00010000 /* 64 KB */
+#define CONFIG_SYS_CPLD_BASE 0x82000000
+#define CONFIG_SYS_CPLD_SIZE 0x00010000 /* 64 KB */
-#define CFG_SRAM_BASE 0x30000000
-#define CFG_SRAM_SIZE 0x00020000 /* 128 KB */
+#define CONFIG_SYS_SRAM_BASE 0x30000000
+#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */
-#define CFG_CS0_CFG 0x05059310 /* ALE active low, data size 4bytes */
-#define CFG_CS2_CFG 0x05059010 /* ALE active low, data size 1byte */
+#define CONFIG_SYS_CS0_CFG 0x05059310 /* ALE active low, data size 4bytes */
+#define CONFIG_SYS_CS2_CFG 0x05059010 /* ALE active low, data size 1byte */
+#define CONFIG_SYS_CS_ALETIMING 0x00000005 /* Use alternative CS timing for CS0 and CS2 */
/* Use SRAM for initial stack */
-#define CFG_INIT_RAM_ADDR CFG_SRAM_BASE /* Initial RAM address */
-#define CFG_INIT_RAM_END CFG_SRAM_SIZE /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_SRAM_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE /* Start of monitor */
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of monitor */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
+#else
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
+#endif
/*
* Serial Port
#error CONFIG_PSC_CONSOLE must be 3
#endif
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * PCI
+ */
+#ifdef CONFIG_PCI
+
+/*
+ * General PCI
+ */
+#define CONFIG_SYS_PCI_MEM_BASE 0xA0000000
+#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
+#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_MMIO_BASE (CONFIG_SYS_PCI_MEM_BASE + CONFIG_SYS_PCI_MEM_SIZE)
+#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
+#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI_IO_PHYS 0x84000000
+#define CONFIG_SYS_PCI_IO_SIZE 0x01000000 /* 16M */
+
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
#endif
/* I2C */
#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_I2C_CMD_TREE
-#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
#if 0
-#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#endif
/*
* EEPROM configuration
*/
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
-#define CFG_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */
/*
* Ethernet configuration
#define CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR 0x1
#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_FEC_AN_TIMEOUT 1
+#define CONFIG_HAS_ETH0
-#if 0
/*
* Configure on-board RTC
*/
-#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-#endif
+#define CONFIG_RTC_M41T62 /* use M41T62 rtc via i2 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
/* This has to be a multiple of the Flash sector size */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE 0x2000
+#ifdef CONFIG_BKUP_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (256K) for env */
+#else
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */
+#endif
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_DATE
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
/*
- * Watchdog timeout = CFG_WATCHDOG_VALUE * 65536 / IPS clock.
- * For example, when IPS is set to 66MHz and CFG_WATCHDOG_VALUE is set
+ * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
+ * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
* to 0xFFFF, watchdog timeouts after about 64s. For details refer
* to chapter 36 of the MPC5121e Reference Manual.
*/
/* #define CONFIG_WATCHDOG */ /* enable watchdog */
-#define CFG_WATCHDOG_VALUE 0xFFFF
+#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#ifdef CONFIG_CMD_KGDB
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
+#define CONFIG_SYS_DCACHE_SIZE 32768
+#define CONFIG_SYS_CACHELINE_SIZE 32
#ifdef CONFIG_CMD_KGDB
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Internal Definitions
#define CONFIG_HOSTNAME ads5121
#define CONFIG_BOOTFILE ads5121/uImage
+#define CONFIG_ROOTPATH /opt/eldk/ppc_6xx
#define CONFIG_LOADADDR 400000 /* default location for tftp and bootm */
#define CONFIG_BAUDRATE 115200
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#define CONFIG_EXTRA_ENV_SETTINGS \
"u-boot_addr_r=200000\0" \
- "kernel_addr_r=200000\0" \
- "fdt_addr_r=400000\0" \
- "ramdisk_addr_r=500000\0" \
+ "kernel_addr_r=600000\0" \
+ "fdt_addr_r=880000\0" \
+ "ramdisk_addr_r=900000\0" \
"u-boot_addr=FFF00000\0" \
- "kernel_addr=FC000000\0" \
- "fdt_addr=FC2C0000\0" \
- "ramdisk_addr=FC300000\0" \
+ "kernel_addr=FFC40000\0" \
+ "fdt_addr=FFEC0000\0" \
+ "ramdisk_addr=FC040000\0" \
"ramdiskfile=ads5121/uRamdisk\0" \
- "fdtfile=ads5121/ads5121.dtb\0" \
"u-boot=ads5121/u-boot.bin\0" \
+ "bootfile=ads5121/uImage\0" \
+ "fdtfile=ads5121/ads5121.dtb\0" \
+ "rootpath=/opt/eldk/ppc_6xx\n" \
"netdev=eth0\0" \
"consdev=ttyPSC0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"addtty=setenv bootargs ${bootargs} " \
"console=${consdev},${baudrate}\0" \
"flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr}\0" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"net_self=tftp ${kernel_addr_r} ${bootfile};" \
"tftp ${ramdisk_addr_r} ${ramdiskfile};" \
- "tftp ${fdt_addr} ${fdtfile};" \
+ "tftp ${fdt_addr_r} ${fdtfile};" \
"run ramargs addip addtty;" \
- "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr}\0"\
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
+ "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
+ "load=tftp ${u-boot_addr_r} ${u-boot}\0" \
"update=protect off ${u-boot_addr} +${filesize};" \
"era ${u-boot_addr} +${filesize};" \
"cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1
#define OF_CPU "PowerPC,5121@0"
-#define OF_SOC "soc@80000000"
-#define OF_SOC_OLD "soc5121@80000000"
+#define OF_SOC_COMPAT "fsl,mpc5121-immr"
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc@80000000/serial@11300"
projects / platform / kernel / u-boot.git / blobdiff