#define CONFIG_ACADIA 1 /* Board is Acadia */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_405EZ 1 /* Specifc 405EZ support*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME acadia
+#include "amcc-common.h"
+
/* Detect Acadia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
66666666 : 33333000)
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */
-
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xfe000000
-#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_CPLD_BASE 0x80000000
#define CFG_NAND_ADDR 0xd0000000
#define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */
*----------------------------------------------------------------------*/
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#define CFG_BASE_BAUD 691200
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
-#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
-#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
+#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*-----------------------------------------------------------------------
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */
#endif
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
/*
#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
-#ifdef CFG_ENV_IS_IN_NAND
+#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
-#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
-#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
/*-----------------------------------------------------------------------
* Ethernet
*----------------------------------------------------------------------*/
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
+#define CONFIG_HAS_ETH0 1
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=acadia\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=acadia/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=fff10000\0" \
"ramdisk_addr=fff20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 acadia/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b ${fileaddr} fffc0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 acadia/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"kozio=bootm ffc60000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
#define CONFIG_SUPPORT_VFAT
/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_USB
/*
#undef CONFIG_CMD_IMLS
#endif
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EZ CPU */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/
-#endif
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CFG_GPIO1_TSRL 0x00000000
#define CFG_GPIO1_TSRH 0x00000000
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
#endif /* __CONFIG_H */