#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/processor.h>
-
#define CFG_GT_6426x GT_64260 /* with a 64260 system controller */
#define CONFIG_ETHER_PORT_MII /* use two MII ports */
#define CONFIG_INTEL_LXT97X /* Intel LXT97X phy */
/* which initialization functions to call for this board */
#define CONFIG_MISC_INIT_R
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
#define CFG_BOARD_ASM_INIT
#define CFG_BOARD_NAME "Zuma APv2"
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_ALTIVEC /* undef to disable */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
- CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_MII /* enable MII commands */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_BSP | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_DATE)
-/* Flash banks JFFS2 should use */
-#define CFG_JFFS2_FIRST_BANK 1
-#define CFG_JFFS2_NUM_BANKS 2
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * JFFS2 partitions
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
+#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2"
+#define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)"
+*/
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* 3| 0|.... ..| 1| 5 | 5 | 5 | 5 | 8 | 5 */
-
#define CFG_8BIT_BOOT_PAR 0xc00b5e7c
#define CFG_MPP_CONTROL_0 0x00007777 /* GPP[7:4] : REQ0[1:0] GNT0[1:0] */
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* L2CR setup -- make sure this is right for your board!
- * look in include/mpc74xx.h for the defines used here
+ * look in include/74xx_7xx.h for the defines used here
*/
#define CFG_L2