* config for XPedite1000 from XES Inc.
* Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
* (C) Copyright 2003 Sandburst Corporation
- * board/config_EBONY.h - configuration for IBM 440GP Ref (Ebony)
+ * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
***********************************************************************/
#ifndef __CONFIG_H
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#define CFG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_IS_IN_EEPROM 1
#define CFG_ENV_SIZE 0x100 /* Size of Environment vars */
#define CFG_ENV_OFFSET 0x100
#define CFG_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */
#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */
#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_I2C | \
- CFG_CMD_DATE | \
- CFG_CMD_BEDBUG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_PING | \
- CFG_CMD_ELF | \
- CFG_CMD_MII | \
- CFG_CMD_DIAG | \
- CFG_CMD_FAT )
-/* CFG_CMD_DHCP | \ */
-/* CFG_CMD_KGDB | \ */
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_BEDBUG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_FAT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT /* let board init pci target */
#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 8192 /* For IBM 440GX CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif