powerpc: Cleanup BOOTFLAG_* references

[platform/kernel/u-boot.git] / include / configs / W7OLMC.h

diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h
index e546369..9eacd82 100644 (file)
--- a/include/configs/W7OLMC.h
+++ b/include/configs/W7OLMC.h
@@ -38,8 +38,11 @@
 #define CONFIG_W7O             1               /* ...on a Wave 7 Optics board  */
 #define CONFIG_W7OLMC          1               /* ...specifically an LMC       */
 
+#define        CONFIG_SYS_TEXT_BASE    0xFFFC0000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1            /* Call board_early_init_f      */
 #define        CONFIG_MISC_INIT_F      1               /* and misc_init_f()            */
+#define        CONFIG_MISC_INIT_R      1               /* and misc_init_r()            */
 
 #define CONFIG_SYS_CLK_FREQ    33333333        /* external frequency to pll    */
 
@@ -65,8 +68,10 @@
 #define CONFIG_LOADS_ECHO      1               /* echo on for serial download  */
 #undef CONFIG_SYS_LOADS_BAUD_CHANGE                    /* disallow baudrate change     */
 
+#define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII             1               /* MII PHY management           */
 #define CONFIG_PHY_ADDR                0               /* PHY address                  */
+#define CONFIG_NET_MULTI
 
 #define CONFIG_RTC_M48T35A     1               /* ST Electronics M48 timekeeper */
 
@@ -122,6 +127,12 @@
 #define CONFIG_SYS_MEMTEST_START       0x0400000       /* memtest works on             */
 #define CONFIG_SYS_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM          */
 
+#define CONFIG_CONS_INDEX      1       /* Use UART0                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
+
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK                    /* external serial clock */
 #define CONFIG_SYS_405_UART_ERRATA_59                  /* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD           384000
@@ -130,8 +141,6 @@
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE      {9600}
 
-#define CONFIG_SYS_CLKS_IN_HZ          1               /* everything, incl board info, in Hz */
-
 #define CONFIG_SYS_LOAD_ADDR           0x100000        /* default load address         */
 #define CONFIG_SYS_EXTBDINFO           1               /* use extended board_info (bd_t) */
 
@@ -207,9 +216,9 @@
 #define CONFIG_SYS_EBC_PB5CR   0xFD21A000
 
 /* bank 6 is unused */
-/* pb6ap = 0 */
+/* PB6AP = 0 */
 #define CONFIG_SYS_EBC_PB6AP   0x00000000
-/* pb6cr = 0 */
+/* PB6CR = 0 */
 #define CONFIG_SYS_EBC_PB6CR   0x00000000
 
 /* bank 7 is LED register */
@@ -272,6 +281,7 @@
  * I2C EEPROM (CAT24WC08) for environment
  */
 #define CONFIG_HARD_I2C                        /* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE           0x7F
 
@@ -308,15 +318,6 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD          0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM          0x02            /* Software reboot              */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400          /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2               /* which serial port to use     */