#define USE_920T_MMU 1
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
-/***********************************************************
- * Command definition
- ***********************************************************/
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- /*CFG_CMD_JFFS2 |*/ \
- /*CFG_CMD_NAND |*/ \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_USB | \
- CFG_CMD_REGINFO | \
- CFG_CMD_FAT | \
- CFG_CMD_DATE | \
- CFG_CMD_ELF | \
- CFG_CMD_DHCP | \
- CFG_CMD_PING | \
- CFG_CMD_BSP)
-
-/* this must be included after the definiton of CONFIG_COMMANDS */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_BSP
+
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
* address 0x50 with 16bit addressing
***********************************************************/
#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CFG_I2C_SPEED 100000 /* I2C speed */
-#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */
+#define CFG_I2C_SPEED 100000 /* I2C speed */
+#define CFG_I2C_SLAVE 0x7F /* I2C slave addr */
#define CFG_I2C_EEPROM_ADDR 0x50
#define CFG_I2C_EEPROM_ADDR_LEN 2
*/
#define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */
#define CS8900_BASE 0x20000300
-#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
+#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */
#define CONFIG_DRIVER_S3C24X0_I2C 1 /* we use the buildin I2C controller */
#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 10.0.0.110
#define CONFIG_SERVERIP 10.0.0.1
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
/*-----------------------------------------------------------------------
* NAND flash settings
*/
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#if defined(CONFIG_CMD_NAND)
-#define CFG_NAND_LEGACY
+#define CONFIG_NAND_LEGACY
#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
-#define NAND_ChipID_UNKNOWN 0x00
+#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
#define NAND_MAX_CHIPS 1
#define CONFIG_MTD_NAND_VERIFY_WRITE 1
#define CONFIG_MTD_NAND_ECC_JFFS2 1
-#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
+#endif
#endif /* __CONFIG_H */