#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
-#define CONFIG_FSL_ELBC
-#define CONFIG_PCI
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_UCP1020_REV_1_3
#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
-#define CONFIG_P1020
#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_LAST_STAGE_INIT
-#if !defined(CONFIG_DONGLE)
-#define CONFIG_SILENT_CONSOLE
-#endif
-
#endif
#if defined(CONFIG_TARGET_UCP1020)
#define CONFIG_UCP1020_REV_1_3
#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
-#define CONFIG_P1020
#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_LAST_STAGE_INIT
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500
-/* #define CONFIG_MPC85xx */
-
#define CONFIG_MP
-#define CONFIG_FSL_LAW
-
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CMD_SATA
#define CONFIG_L2_CACHE
#define CONFIG_BTB
-#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
-
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
/* DDR Setup */
#define CONFIG_DDR_ECC_ENABLE
-#define CONFIG_SYS_FSL_DDR3
#ifndef CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
/* Default settings for DDR3 */
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_CMD_PCI
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
/*
* Command line configuration.
*/
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_DATE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_CRAMFS
/*
* USB
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
#endif
#endif
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_MMC_SPI
#define CONFIG_CMD_MMC_SPI
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
#endif
/* Misc Extra Settings */
#define CONFIG_BOOTARGS /* the boot command will set bootargs */
-#define CONFIG_BAUDRATE 115200
-
#if defined(CONFIG_DONGLE)
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run prog_spi_mbrbootcramfs\0" \
"bootfile=uImage\0" \
#if defined(CONFIG_UCP1020T1)
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
"bootfile=uImage\0" \
#else /* For Arcturus Modules */
-#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run norkernel\0" \
"bootfile=uImage\0" \