Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

[platform/kernel/u-boot.git] / include / configs / Total5200.h

diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h
index 75d1985..3bb975c 100644 (file)
--- a/include/configs/Total5200.h
+++ b/include/configs/Total5200.h
@@ -41,12 +41,20 @@
  */
 
 #define CONFIG_MPC5xxx         1       /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200         1       /* (more precisely a MPC5200 CPU) */
 #define CONFIG_TOTAL5200       1       /* ... on Total5200 board */
 
-#define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFFF00000  boot high (standard configuration)
+ * 0xFE000000  boot low
+ * 0x00100000  boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define        CONFIG_SYS_TEXT_BASE    0xFFF00000
+#endif
 
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM          0x02    /* Software reboot           */
+#define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
 
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
 
@@ -73,7 +81,6 @@
 #define CONFIG_SPLASH_SCREEN
 
 
-#ifdef CONFIG_MPC5200  /* MGT5100 PCI is not supported yet. */
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
@@ -98,12 +105,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER       8  /* use 8 rx buffer on eepro100  */
 #define CONFIG_NS8382X         1
 
-#else  /* MGT5100 */
-
-#define CONFIG_MII             1
-
-#endif
-
 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -127,9 +128,7 @@
  */
 #include <config_cmd_default.h>
 
-#if defined(CONFIG_MPC5200)
-    #define CONFIG_CMD_PCI
-#endif
+#define CONFIG_CMD_PCI
 
 #define CONFIG_CMD_BMP
 #define CONFIG_CMD_EEPROM
@@ -140,7 +139,7 @@
 #define CONFIG_CMD_USB
 
 
-#if (TEXT_BASE == 0xFE000000)          /* Boot low */
+#if (CONFIG_SYS_TEXT_BASE == 0xFE000000)               /* Boot low */
 #   define CONFIG_SYS_LOWBOOT          1
 #endif
 
@@ -176,12 +175,10 @@
 
 #define CONFIG_BOOTCOMMAND     "run flash_self"
 
-#if defined(CONFIG_MPC5200)
 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK         /* define for 133MHz speed */
-#endif
 
 /*
  * I2C configuration
@@ -249,13 +246,13 @@
 
 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_SIZE       /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 
 #define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -268,6 +265,7 @@
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC     1
+#define CONFIG_MPC5xxx_FEC_SEVENWIRE
 /* dummy, 7-wire FEC does not have phy address */
 #define CONFIG_PHY_ADDR                0x00
 
@@ -325,17 +323,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
-
-#if defined (CONFIG_MGT5100)
-#   define CONFIG_BOARD_EARLY_INIT_R   /* switch from CS_BOOT to CS0 */
-#endif
 
 #if CONFIG_TOTAL5200_REV==1
 #   define CONFIG_SYS_BOOTCS_START     CONFIG_SYS_FLASH_BASE
@@ -396,6 +385,7 @@
 #define        CONFIG_IDE_RESET                /* reset for ide supported      */
 #define CONFIG_IDE_PREINIT
 
+#define CONFIG_SYS_ATA_CS_ON_I2C2
 #define CONFIG_SYS_IDE_MAXBUS          1       /* max. 1 IDE bus               */
 #define CONFIG_SYS_IDE_MAXDEVICE       1       /* max. 1 drive per IDE bus     */