/*
- * (C) Copyright 2000-2003
+ * (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define CONFIG_MPC866 1 /* This is a MPC866 CPU */
#define CONFIG_TQM866M 1 /* ...on a TQM8xxM module */
-#define CFG_8XX_XIN 10000000 /* XXX XXX XXX */
+#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */
+#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */
+#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */
+#define CONFIG_8xx_CPUCLK_DEFAULT 50000000 /* 50 MHz - CPU default clock */
+ /* (it will be used if there is no */
+ /* 'cpuclk' variable with valid value) */
+
+#undef CFG_MEASURE_CPUCLK /* Measure real cpu clock */
+ /* (function measure_gclk() */
+ /* will be called) */
+#ifdef CFG_MEASURE_CPUCLK
+#define CFG_8XX_XIN 10000000 /* measure_gclk() needs this */
+#endif
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
-#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOARD_TYPES 1 /* support board types */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_8xx\0" \
- "bootfile=/tftpboot/TQM855M/uImage\0" \
- "kernel_addr=40080000\0" \
- "ramdisk_addr=40180000\0" \
+ "bootfile=/tftpboot/TQM866M/uImage\0" \
+ "fdt_addr=400C0000\0" \
+ "kernel_addr=40100000\0" \
+ "ramdisk_addr=40280000\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "update=protect off 40000000 +${filesize};" \
+ "erase 40000000 +${filesize};" \
+ "cp.b 200000 40000000 ${filesize};" \
+ "protect on 40000000 +${filesize}\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
#define CFG_I2C_SLAVE 0xFE
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
#endif /* CONFIG_SOFT_I2C */
#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C256 */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */
#define CFG_EEPROM_PAGE_WRITE_BITS 4
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */
+
+#define CONFIG_TIMESTAMP /* but print image timestmps */
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
- CFG_CMD_IDE | \
- CFG_CMD_I2C | \
- CFG_CMD_DATE )
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if 0
-#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-#endif
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */
+/* use CFI flash driver */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
+
/*-----------------------------------------------------------------------
* Hardware Information Block
*/
#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
-#ifndef CONFIG_CAN_DRIVER
+#ifndef CONFIG_CAN_DRIVER
#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#else /* we must activate GPL5 in the SIUMCR for CAN */
#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * set PLL multiplication factor
- */
-#if defined(CONFIG_133MHz)
- /* for 133 MHz, we use a 10 MHz clock:
- * MFN = 0x09, MFD = 0x1D, S = 0, MFI = 13
- */
-#define CFG_PLPRCR \
- ( 9 << PLPRCR_MFN_SHIFT | 0x1D << PLPRCR_MFD_SHIFT | \
- 0 << PLPRCR_S_SHIFT | 0x0D << PLPRCR_MFI_SHIFT | \
- PLPRCR_TEXPS )
-#elif defined(CONFIG_80MHz) /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_PLPRCR \
- ( (5-1)<<PLPRCR_MFI_SHIFT | PLPRCR_TEXPS )
-#else /* up to 66 MHz we use a 1:1 clock */
-#define CFG_PLPRCR ( PLPRCR_SPLSS | PLPRCR_TEXPS )
-#endif /* CONFIG_??MHz */
-
-/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
-#if defined(CONFIG_133MHz) /* for 133 MHz, we use a 10 MHz clock * 13 */
-#define CFG_SCCR (/* SCCR_TBS | */ \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-#elif defined(CONFIG_80MHz) /* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CFG_SCCR (/* SCCR_TBS | */ \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
-#else /* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR (SCCR_TBS | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-#endif /* CONFIG_??MHz */
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
*-----------------------------------------------------------------------
*
*/
-#define CFG_DER 0
+#define CFG_DER 0
/*
* Init Memory Controller:
#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/*
- * FLASH timing:
- */
-#if defined(CONFIG_133MHz)
-/* 133 MHz CPU - 66 MHz bus: */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_100MHz)
-/* 100 MHz CPU - 50 MHz bus: */
-#elif defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | 0 | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else /* 50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif /*CONFIG_??MHz */
+ * FLASH timing: Default value of OR0 after reset
+ */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
+ OR_SCY_15_CLK | OR_TRLX)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
*/
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
+#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CFG_OR_TIMING_SDRAM 0x00000A00
#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#ifndef CONFIG_CAN_DRIVER
-#define CFG_OR3_PRELIM CFG_OR2_PRELIM
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_OR3_PRELIM CFG_OR2_PRELIM
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
+#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI)
#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
#endif /* CONFIG_CAN_DRIVER */
/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
+ */
+#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
+
+/*
+ * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
*
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
+ * CPUclock(MHz) * 31.2
+ * CFG_MAMR_PTA = ----------------------------------- with DFBRG = 0
+ * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
+ * CPU clock = 15 MHz: CFG_MAMR_PTA = 29 -> 4 * 7.73 us
+ * CPU clock = 50 MHz: CFG_MAMR_PTA = 97 -> 4 * 7.76 us
+ * CPU clock = 66 MHz: CFG_MAMR_PTA = 128 -> 4 * 7.75 us
+ * CPU clock = 133 MHz: CFG_MAMR_PTA = 255 -> 4 * 7.67 us
*
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-#if defined(CONFIG_133MHz)
-#define CFG_MAMR_PTA 129
-#elif defined(CONFIG_100MHz)
-#define CFG_MAMR_PTA 98
-#elif defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA 156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA 129
-#else /* 50 MHz */
-#define CFG_MAMR_PTA 98
-#endif /*CONFIG_??MHz */
+ * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
+ * be met also in the default configuration, i.e. if environment variable
+ * 'cpuclk' is not set.
+ */
+#define CFG_MAMR_PTA 97
/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
+ * Memory Periodic Timer Prescaler Register (MPTPR) values.
*/
-#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16
+/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8
/*
* MAMR settings for SDRAM
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* Internal Definitions
*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_SCC1_ENET