#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
+#if defined(CONFIG_TQM8548_BE)
+#define CONFIG_SYS_TEXT_BASE 0xfff80000
+#else
+#define CONFIG_SYS_TEXT_BASE 0xfffc0000
+#endif
+
+#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE)
+#define CONFIG_TQM8548
+#endif
+
#define CONFIG_PCI
+#ifndef CONFIG_TQM8548_AG
+#define CONFIG_PCI1 /* PCI/PCI-X controller */
+#endif
+#ifdef CONFIG_TQM8548
+#define CONFIG_PCIE1 /* PCI Express interface */
+#endif
+
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */
-#ifdef CONFIG_TQM8548
-#define CONFIG_PCI1
-#define CONFIG_PCIE1
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
-#endif
#define CONFIG_TSEC_ENET /* tsec ethernet support */
* NAND flash support (disabled by default)
*
* Warning: NAND support will likely increase the U-Boot image size
- * to more than 256 KB. Please adjust TEXT_BASE if necessary.
+ * to more than 256 KB. Please adjust CONFIG_SYS_TEXT_BASE if necessary.
*/
-#undef CONFIG_NAND
+#ifdef CONFIG_TQM8548_BE
+#define CONFIG_NAND
+#endif
/*
* MPC8540 and MPC8548 don't have CPM module
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-#undef CONFIG_CAN_DRIVER /* CAN Driver support */
+#if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE)
+#define CONFIG_CAN_DRIVER /* CAN Driver support */
+#endif
/*
* sysclk for MPC85xx
#define CONFIG_SYS_MEMTEST_START 0x00000000
#define CONFIG_SYS_MEMTEST_END 0x10000000
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
#ifdef CONFIG_TQM_BIGFLASH
-#define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */
-#else /* !CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
-#endif /* CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000)
-#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000)
-#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000)
+#define CONFIG_SYS_CCSRBAR 0xA0000000
+#else
+#define CONFIG_SYS_CCSRBAR 0xE0000000
+#endif
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+
+#if defined(CONFIG_TQM_BIGFLASH) || \
+ (!defined(CONFIG_TQM8548_AG) && !defined(CONFIG_TQM8548_BE))
+#define CONFIG_SYS_PPC_DDR_WIMGE (MAS2_I | MAS2_G)
+#define CONFIG_SYS_DDR_EARLY_SIZE_MB (512)
+#else
+#define CONFIG_SYS_PPC_DDR_WIMGE (0)
+#define CONFIG_SYS_DDR_EARLY_SIZE_MB (2 * 1024)
+#endif
+
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#ifdef CONFIG_TQM8548_AG
+#define CONFIG_VERY_BIG_RAM
+#endif
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
/* TQM8540 & 8560 need DLL-override */
-#define CONFIG_DDR_DLL /* DLL fix needed */
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
#define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */
#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */
#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */
/*
- * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM
- * series while new boards have 'N' type Flashes from the S29GLxxxN
- * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
- */
-#ifdef CONFIG_TQM8548
-#define CONFIG_TQM_FLASH_N_TYPE
-#endif /* CONFIG_TQM8548 */
-
-/*
* Flash on the Local Bus
*/
#ifdef CONFIG_TQM_BIGFLASH
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
/*
* Note: when changing the Local Bus clock divider you have to
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_CCSRBAR \
+ 0x04010000) /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (~CONFIG_SYS_TEXT_BASE + 1)/* Reserved for Monitor */
#define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserved for malloc */
/* Serial Port */
#else /* !CONFIG_TQM8560 */
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
/* NAND FLASH */
#ifdef CONFIG_NAND
-#undef CONFIG_NAND_LEGACY
-
#define CONFIG_NAND_FSL_UPM 1
#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */
#define CONFIG_SYS_NAND_CS_DIST 0x200
#define CONFIG_SYS_NAND_SIZE 0x8000
-#define CONFIG_SYS_NAND0_BASE (CONFIG_SYS_CCSRBAR + 0x03010000)
-#define CONFIG_SYS_NAND1_BASE (CONFIG_SYS_NAND0_BASE + CONFIG_SYS_NAND_CS_DIST)
-#define CONFIG_SYS_NAND2_BASE (CONFIG_SYS_NAND1_BASE + CONFIG_SYS_NAND_CS_DIST)
-#define CONFIG_SYS_NAND3_BASE (CONFIG_SYS_NAND2_BASE + CONFIG_SYS_NAND_CS_DIST)
-
-#define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
-#define NAND_MAX_CHIPS 1
-
-#if (CONFIG_SYS_MAX_NAND_DEVICE == 1)
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE }
-#elif (CONFIG_SYS_MAX_NAND_DEVICE == 2)
-#define CONFIG_SYS_NAND_QUIET_TEST 1
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, \
- CONFIG_SYS_NAND1_BASE, \
-}
-#elif (CONFIG_SYS_MAX_NAND_DEVICE == 4)
-#define CONFIG_SYS_NAND_QUIET_TEST 1
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, \
- CONFIG_SYS_NAND1_BASE, \
- CONFIG_SYS_NAND2_BASE, \
- CONFIG_SYS_NAND3_BASE, \
-}
-#endif
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_CCSRBAR + 0x03010000)
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#define CONFIG_SYS_NAND_MAX_CHIPS 2 /* Number of chips per device */
/* CS3 for NAND Flash */
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_NAND0_BASE & BR_BA) | BR_PS_8 | \
- BR_MS_UPMB | BR_V)
+#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA) | \
+ BR_PS_8 | BR_MS_UPMB | BR_V)
#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | OR_UPM_BI)
-#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */
+#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */
#endif /* CONFIG_NAND */
* General PCI
* Addresses are mapped 1-1.
*/
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE (CONFIG_SYS_CCSRBAR + 0x02000000)
-#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_BUS (CONFIG_SYS_CCSRBAR + 0x02000000)
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BUS
#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */
#ifdef CONFIG_PCIE1
* Addresses are mapped 1-1.
*/
#ifdef CONFIG_TQM_BIGFLASH
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xb0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xb0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BASE 0xaf000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0xaf000000
#else /* !CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BASE 0xef000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0xef000000
#endif /* CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
-#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BASE
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS
+#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS
#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */
#endif /* CONFIG_PCIE1 */
#endif /* CONFIG_PCI */
-#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#ifdef CONFIG_TQM_FLASH_N_TYPE
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */
-#else /* !CONFIG_TQM_FLASH_N_TYPE */
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
-#endif /* CONFIG_TQM_FLASH_N_TYPE */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
#define CONFIG_JFFS2_NAND 1
-#ifdef CONFIG_JFFS2_CMDLINE
+#ifdef CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nand0=TQM85xx-nand"
#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-"
#else
#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */
#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */
-#endif /* CONFIG_JFFS2_CMDLINE */
+#endif /* CONFIG_CMD_MTDPARTS */
#endif /* CONFIG_NAND */
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
+#ifndef CONFIG_TQM8548_AG
#define CONFIG_CMD_DATE
+#endif
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DTT
#define CONFIG_CMD_MII
+#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
MK_STR(CONFIG_HOSTNAME)".dtb\0"
#define CONFIG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0"
#define CONFIG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \
- "uboot_addr="MK_STR(TEXT_BASE)"\0"
+ "uboot_addr="MK_STR(CONFIG_SYS_TEXT_BASE)"\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_ENV_BOOTFILE \
CONFIG_ENV_FDT_FILE \
- CONFIG_ENV_CONSDEV \
+ CONFIG_ENV_CONSDEV \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath\0" \
"fdt_addr=ffec0000\0" \
"kernel_addr=ffd00000\0" \
"ramdisk_addr=ff800000\0" \
- CONFIG_ENV_UBOOT \
+ CONFIG_ENV_UBOOT \
"load=tftp 100000 $uboot\0" \
"update=protect off $uboot_addr +$filesize;" \
"erase $uboot_addr +$filesize;" \
- "cp.b 100000 $uboot_addr $filesize;" \
- "setenv filesize;saveenv\0" \
+ "cp.b 100000 $uboot_addr $filesize" \
"upd=run load update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
projects / platform / kernel / u-boot.git / blobdiff