* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC83xx 1 /* MPC83xx family */
#define CONFIG_MPC834x 1 /* MPC834x specific */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_TQM834X 1 /* TQM834X board specific */
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
/* board pre init: do not call, nothing to do */
-#undef CONFIG_BOARD_EARLY_INIT_F
/* detect the number of flash banks */
#define CONFIG_BOARD_EARLY_INIT_R
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes/write */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */
-#define CONFIG_SYS_I2C_MULTI_EEPROMS /* more than one eeprom */
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-
/*
* TSEC
*/
* General PCI
* Addresses are mapped 1-1.
*/
-#define CONFIG_PCI
#if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI1 host bridge */
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
-
/*
* Miscellaneous configurable options
*/
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#undef CONFIG_WATCHDOG /* watchdog disabled */
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 400000
-#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
* JFFS2 partitions
*/
/* mtdparts command line support */
-#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=TQM834x-0"