*/
#define CONFIG_E300 1 /* E300 Family */
-/* IMMR Base Address Register, use Freescale default: 0xff400000 */
-#define CONFIG_SYS_IMMR 0xff400000
-
-/*
- * Local Bus LCRR
- * LCRR: DLL bypass, Clock divider is 8
- *
- * for CSB = 266 MHz it gives LCB clock frequency = 33 MHz
- *
- * External Local Bus rate is
- * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
-
/* board pre init: do not call, nothing to do */
/* detect the number of flash banks */
* DDR Setup
*/
/* DDR is system memory*/
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define DDR_CASLAT_25 /* CASLAT set to 2.5 */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00100000
/*
* FLASH on the Local Bus
#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */
-#undef CONFIG_EEPRO100
-#define CONFIG_EEPRO100
-#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE
/*
* Environment
*/
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
-#define CONFIG_ENV_SIZE 0x8000 /* 32K max size */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_SYS_SICRH 0
#define CONFIG_SYS_SICRL SICRL_LDP_A
-/* i-cache and d-cache disabled */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
/* PCI */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 400000
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=tqm834x\0" \