#define CONFIG_E300 1 /* E300 Family */
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC834X 1 /* MPC834X specific */
+#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_TQM834X 1 /* TQM834X board specific */
/* IMMR Base Addres Register, use Freescale default: 0xff400000 */
-#define CFG_IMMRBAR 0xff400000
+#define CFG_IMMR 0xff400000
/* System clock. Primary input clock when in PCI host mode */
#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_BASE 0x80000000 /* start of FLASH */
+#define CFG_FLASH_SIZE 8 /* FLASH size in MB */
/* buffered writes in the AMD chip set is not supported yet */
#undef CFG_FLASH_USE_BUFFER_WRITE
* When CFG_MAX_FLASH_BANKS_DETECT is defined, the actual number of Flash
* banks has to be determined at runtime and stored in a gloabl variable
* tqm834x_num_flash_banks. The value of CFG_MAX_FLASH_BANKS_DETECT is only
- * used insted of CFG_MAX_FLASH_BANKS to allocate the array flash_info, and
+ * used instead of CFG_MAX_FLASH_BANKS to allocate the array flash_info, and
* should be made sufficiently large to accomodate the number of banks that
- * might acutally be detected. Since most (all?) Flash related functions use
+ * might actually be detected. Since most (all?) Flash related functions use
* CFG_MAX_FLASH_BANKS as the number of actual banks on the board, it is
* defined as tqm834x_num_flash_banks.
*/
#define CFG_MAX_FLASH_BANKS_DETECT 2
-#ifndef __ASSEMBLY__
+#ifndef __ASSEMBLY__
extern int tqm834x_num_flash_banks;
#endif
#define CFG_MAX_FLASH_BANKS (tqm834x_num_flash_banks)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMRBAR + 0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR + 0x4600)
+#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
/*
* I2C
*/
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_FSL_I2C
#define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */
#define CFG_I2C_SLAVE 0x7F /* slave address */
#define CFG_I2C_OFFSET 0x3000
#define CONFIG_MII
#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMRBAR + CFG_TSEC1_OFFSET)
+#define CFG_TSEC1 (CFG_IMMR + CFG_TSEC1_OFFSET)
#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMRBAR + CFG_TSEC2_OFFSET)
+#define CFG_TSEC2 (CFG_IMMR + CFG_TSEC2_OFFSET)
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_NET_MULTI
#endif
-#define CONFIG_MPC83XX_TSEC1 1
-#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC83XX_TSEC2 1
-#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-
#undef CONFIG_EEPRO100
#define CONFIG_EEPRO100
#undef CONFIG_TULIP
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-/* Common commands */
-#define CFG_CMD_TQM8349_COMMON CFG_CMD_DATE | CFG_CMD_I2C | CFG_CMD_DTT\
- | CFG_CMD_PING | CFG_CMD_EEPROM \
- | CFG_CMD_MII | CFG_CMD_JFFS2
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
-#if defined(CFG_RAMBOOT)
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI \
- | CFG_CMD_TQM8349_COMMON) \
- & \
- ~(CFG_CMD_ENV | CFG_CMD_LOADS))
-#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_TQM8349_COMMON) \
- & \
- ~(CFG_CMD_ENV | CFG_CMD_LOADS))
+ #define CONFIG_CMD_PCI
#endif
-#else /* CFG_RAMBOOT */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI \
- | CFG_CMD_TQM8349_COMMON)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_TQM8349_COMMON)
+#if defined(CFG_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
#endif
-#endif /* CFG_RAMBOOT */
-
-#include <cmd_confdefs.h>
-
/*
* Miscellaneous configurable options
*/
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
*/
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
HRCWH_TSEC2M_IN_GMII )
#endif
+/* System IO Config */
+#define CFG_SICRH SICRH_TSOBI1
+#define CFG_SICRL SICRL_LDP_A
+
/* i-cache and d-cache disabled */
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL CFG_HID0_INIT
-#define CFG_HID2 0x000000000
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL CFG_HID0_INIT
+#define CFG_HID2 HID2_HBE
+
+/* DDR 0 - 512M */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_SDRAM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* stack in DCACHE @ 512M (no backing mem) */
+#define CFG_IBAT2L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+
+/* PCI */
+#ifdef CONFIG_PCI
+#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
+#else
+#define CFG_IBAT3L (0)
+#define CFG_IBAT3U (0)
+#define CFG_IBAT4L (0)
+#define CFG_IBAT4U (0)
+#define CFG_IBAT5L (0)
+#define CFG_IBAT5U (0)
+#endif
+
+/* IMMRBAR */
+#define CFG_IBAT6L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U (CFG_IMMR | BATU_BL_1M | BATU_VS | BATU_VP)
+
+/* FLASH */
+#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT7U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+#define CFG_DBAT4L CFG_IBAT4L
+#define CFG_DBAT4U CFG_IBAT4U
+#define CFG_DBAT5L CFG_IBAT5L
+#define CFG_DBAT5U CFG_IBAT5U
+#define CFG_DBAT6L CFG_IBAT6L
+#define CFG_DBAT6U CFG_IBAT6U
+#define CFG_DBAT7L CFG_IBAT7L
+#define CFG_DBAT7U CFG_IBAT7U
/*
* Internal Definitions
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
"netdev=eth0\0" \
"hostname=tqm83xx\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
- "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"bootfile=/tftpboot/tqm83xx/uImage\0" \