* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC83XX 1 /* MPC83XX family */
-#define CONFIG_MPC834X 1 /* MPC834X specific */
+#define CONFIG_MPC83xx 1 /* MPC83xx family */
+#define CONFIG_MPC834x 1 /* MPC834x specific */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_TQM834X 1 /* TQM834X board specific */
/* IMMR Base Addres Register, use Freescale default: 0xff400000 */
-#define CFG_IMMR 0xff400000
+#define CONFIG_SYS_IMMR 0xff400000
/* System clock. Primary input clock when in PCI host mode */
#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */
* External Local Bus rate is
* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
*/
-#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
+#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8)
/* board pre init: do not call, nothing to do */
#undef CONFIG_BOARD_EARLY_INIT_F
/*
* DDR Setup
*/
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define DDR_CASLAT_25 /* CASLAT set to 2.5 */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00000000 /* memtest region */
-#define CFG_MEMTEST_END 0x00100000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00100000
/*
* FLASH on the Local Bus
*/
-#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_BASE 0x80000000 /* start of FLASH */
-#define CFG_FLASH_SIZE 8 /* FLASH size in MB */
-
-/* buffered writes in the AMD chip set is not supported yet */
-#undef CFG_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_BASE 0x80000000 /* start of FLASH */
+#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size in MB */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/*
* FLASH bank number detection
*/
/*
- * When CFG_MAX_FLASH_BANKS_DETECT is defined, the actual number of Flash
+ * When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, the actual number of Flash
* banks has to be determined at runtime and stored in a gloabl variable
- * tqm834x_num_flash_banks. The value of CFG_MAX_FLASH_BANKS_DETECT is only
- * used instead of CFG_MAX_FLASH_BANKS to allocate the array flash_info, and
+ * tqm834x_num_flash_banks. The value of CONFIG_SYS_MAX_FLASH_BANKS_DETECT is only
+ * used instead of CONFIG_SYS_MAX_FLASH_BANKS to allocate the array flash_info, and
* should be made sufficiently large to accomodate the number of banks that
* might actually be detected. Since most (all?) Flash related functions use
- * CFG_MAX_FLASH_BANKS as the number of actual banks on the board, it is
+ * CONFIG_SYS_MAX_FLASH_BANKS as the number of actual banks on the board, it is
* defined as tqm834x_num_flash_banks.
*/
-#define CFG_MAX_FLASH_BANKS_DETECT 2
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
#ifndef __ASSEMBLY__
extern int tqm834x_num_flash_banks;
#endif
-#define CFG_MAX_FLASH_BANKS (tqm834x_num_flash_banks)
+#define CONFIG_SYS_MAX_FLASH_BANKS (tqm834x_num_flash_banks)
-#define CFG_MAX_FLASH_SECT 512 /* max sectors per device */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */
/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BR_BA) | \
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BR_BA) | \
BR_MS_GPCM | BR_PS_32 | BR_V)
/* FLASH timing (0x0000_0c54) */
-#define CFG_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_0b10 | \
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | \
OR_GPCM_SCY_5 | OR_GPCM_TRLX)
-#define CFG_PRELIM_OR_AM 0xc0000000 /* OR addr mask: 1 GiB */
+#define CONFIG_SYS_PRELIM_OR_AM 0xc0000000 /* OR addr mask: 1 GiB */
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CFG_LBLAWAR0_PRELIM 0x8000001D /* 1 GiB window size (2^(size + 1)) */
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001D /* 1 GiB window size (2^(size + 1)) */
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
/* disable remaining mappings */
-#define CFG_BR1_PRELIM 0x00000000
-#define CFG_OR1_PRELIM 0x00000000
-#define CFG_LBLAWBAR1_PRELIM 0x00000000
-#define CFG_LBLAWAR1_PRELIM 0x00000000
-
-#define CFG_BR2_PRELIM 0x00000000
-#define CFG_OR2_PRELIM 0x00000000
-#define CFG_LBLAWBAR2_PRELIM 0x00000000
-#define CFG_LBLAWAR2_PRELIM 0x00000000
-
-#define CFG_BR3_PRELIM 0x00000000
-#define CFG_OR3_PRELIM 0x00000000
-#define CFG_LBLAWBAR3_PRELIM 0x00000000
-#define CFG_LBLAWAR3_PRELIM 0x00000000
-
-#define CFG_BR4_PRELIM 0x00000000
-#define CFG_OR4_PRELIM 0x00000000
-#define CFG_LBLAWBAR4_PRELIM 0x00000000
-#define CFG_LBLAWAR4_PRELIM 0x00000000
-
-#define CFG_BR5_PRELIM 0x00000000
-#define CFG_OR5_PRELIM 0x00000000
-#define CFG_LBLAWBAR5_PRELIM 0x00000000
-#define CFG_LBLAWAR5_PRELIM 0x00000000
-
-#define CFG_BR6_PRELIM 0x00000000
-#define CFG_OR6_PRELIM 0x00000000
-#define CFG_LBLAWBAR6_PRELIM 0x00000000
-#define CFG_LBLAWAR6_PRELIM 0x00000000
-
-#define CFG_BR7_PRELIM 0x00000000
-#define CFG_OR7_PRELIM 0x00000000
-#define CFG_LBLAWBAR7_PRELIM 0x00000000
-#define CFG_LBLAWAR7_PRELIM 0x00000000
+#define CONFIG_SYS_BR1_PRELIM 0x00000000
+#define CONFIG_SYS_OR1_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWBAR1_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x00000000
+
+#define CONFIG_SYS_BR2_PRELIM 0x00000000
+#define CONFIG_SYS_OR2_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWBAR2_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWAR2_PRELIM 0x00000000
+
+#define CONFIG_SYS_BR3_PRELIM 0x00000000
+#define CONFIG_SYS_OR3_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWBAR3_PRELIM 0x00000000
+#define CONFIG_SYS_LBLAWAR3_PRELIM 0x00000000
/*
* Monitor config
*/
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+# undef CONFIG_SYS_RAMBOOT
#endif
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB = 3 sect. for Mon */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/*
* I2C
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED 400000 /* I2C speed: 400KHz */
-#define CFG_I2C_SLAVE 0x7F /* slave address */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed: 400KHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */
-#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes per write */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
/*
* TSEC
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_MII
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR + CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR + CFG_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI1 host bridge */
-#define CFG_PCI1_MEM_BASE 0xc0000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000
+#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */
#undef CONFIG_EEPRO100
#define CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR CFG_PCI1_IO_BASE
- #define PCI_ENET0_MEMADDR CFG_PCI1_MEM_BASE
+ #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE
+ #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_MEM_BASE
#define PCI_IDSEL_NUMBER 0x1c /* slot0 (IDSEL) = 28 */
#endif
-#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
* Environment
*/
-#define CONFIG_ENV_OVERWRITE
-
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */
+#define CONFIG_ENV_SIZE 0x8000 /* 32K max size */
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
-#if defined(CFG_RAMBOOT)
- #undef CONFIG_CMD_ENV
+#if defined(CONFIG_SYS_RAMBOOT)
+ #undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
#undef CONFIG_WATCHDOG /* watchdog disabled */
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN_4X1 |\
HRCWL_CORE_TO_CSB_2X1)
#if defined(PCI_64BIT)
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_64_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_TSEC1M_IN_GMII |\
HRCWH_TSEC2M_IN_GMII )
#else
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_32_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
#endif
/* System IO Config */
-#define CFG_SICRH SICRH_TSOBI1
-#define CFG_SICRL SICRL_LDP_A
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
/* i-cache and d-cache disabled */
-#define CFG_HID0_INIT 0x000000000
-#define CFG_HID0_FINAL CFG_HID0_INIT
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL CONFIG_SYS_HID0_INIT
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR 0 - 512M */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U (CFG_SDRAM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in DCACHE @ 512M (no backing mem) */
-#define CFG_IBAT2L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
/* PCI */
#ifdef CONFIG_PCI
-#define CFG_IBAT3L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT3U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_MEM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT4U (CFG_PCI1_MEM_BASE + 0x10000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT5L (CFG_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U (CFG_PCI1_IO_BASE + 0x10000000 | BATU_BL_16M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_MEMCOHERENCE | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_IO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_IO_BASE | BATU_BL_16M | BATU_VS | BATU_VP)
#else
-#define CFG_IBAT3L (0)
-#define CFG_IBAT3U (0)
-#define CFG_IBAT4L (0)
-#define CFG_IBAT4U (0)
-#define CFG_IBAT5L (0)
-#define CFG_IBAT5U (0)
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+#define CONFIG_SYS_IBAT5L (0)
+#define CONFIG_SYS_IBAT5U (0)
#endif
/* IMMRBAR */
-#define CFG_IBAT6L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U (CFG_IMMR | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (CONFIG_SYS_IMMR | BATU_BL_1M | BATU_VS | BATU_VP)
/* FLASH */
-#define CFG_IBAT7L (CFG_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT7U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
-#define CFG_DBAT2L CFG_IBAT2L
-#define CFG_DBAT2U CFG_IBAT2U
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
-#define CFG_DBAT4L CFG_IBAT4L
-#define CFG_DBAT4U CFG_IBAT4U
-#define CFG_DBAT5L CFG_IBAT5L
-#define CFG_DBAT5U CFG_IBAT5U
-#define CFG_DBAT6L CFG_IBAT6L
-#define CFG_DBAT6U CFG_IBAT6U
-#define CFG_DBAT7L CFG_IBAT7L
-#define CFG_DBAT7U CFG_IBAT7U
+#define CONFIG_SYS_IBAT7L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT7U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* Internal Definitions
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
+ "addcons=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs_old=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ "flash_self_old=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 400000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
+ "flash_self=run ramargs addip addcons;" \
+ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
+ "net_nfs_old=tftp 400000 ${bootfile};" \
+ "run nfsargs addip addcons;bootm\0" \
+ "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
+ "tftp ${fdt_addr_r} ${fdt_file}; " \
+ "run nfsargs addip addcons; " \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/tqm834x/uImage\0" \
- "kernel_addr=80060000\0" \
- "ramdisk_addr=80160000\0" \
- "load=tftp 100000 /tftpboot/tqm834x/u-boot.bin\0" \
- "update=protect off 80000000 8003ffff; " \
- "era 80000000 8003ffff; cp.b 100000 80000000 40000\0" \
+ "bootfile=tqm834x/uImage\0" \
+ "fdtfile=tqm834x/tqm834x.dtb\0" \
+ "kernel_addr_r=400000\0" \
+ "fdt_addr_r=600000\0" \
+ "ramdisk_addr_r=800000\0" \
+ "kernel_addr=800C0000\0" \
+ "fdt_addr=800A0000\0" \
+ "ramdisk_addr=80300000\0" \
+ "u-boot=tqm834x/u-boot.bin\0" \
+ "load=tftp 200000 ${u-boot}\0" \
+ "update=protect off 80000000 +${filesize};" \
+ "era 80000000 +${filesize};" \
+ "cp.b 200000 80000000 ${filesize}\0" \
"upd=run load update\0" \
""
* JFFS2 partitions
*/
/* mtdparts command line support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=TQM834x-0"
/* default mtd partition table */