Makefile: move all Power Architecture boards into boards.cfg

[platform/kernel/u-boot.git] / include / configs / TQM5200.h

diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index db7f51d..f9d1110 100644 (file)
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -37,6 +37,17 @@
 #define CONFIG_TQM5200         1       /* ... on TQM5200 module                */
 #undef CONFIG_TQM5200_REV100           /*  define for revision 100 modules     */
 
+/*
+ * Valid values for CONFIG_SYS_TEXT_BASE are:
+ * 0xFC000000  boot low (standard configuration with room for
+ *             max 64 MByte Flash ROM)
+ * 0xFFF00000  boot high (for a backup copy of U-Boot)
+ * 0x00100000  boot from RAM (for testing only)
+ */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xFC000000
+#endif
+
 /* On a Cameron or on a FO300 board or ...                             */
 #if !defined(CONFIG_CAM5200) && !defined(CONFIG_FO300)
 #define CONFIG_STK52XX         1       /* ... on a STK52XX board               */
@@ -214,7 +225,7 @@
 
 #define        CONFIG_TIMESTAMP                /* display image timestamps */
 
-#if (TEXT_BASE != 0xFFF00000)
+#if (CONFIG_SYS_TEXT_BASE != 0xFFF00000)
 #   define CONFIG_SYS_LOWBOOT          1       /* Boot low */
 #endif
 
@@ -253,7 +264,7 @@
 #define CUSTOM_ENV_SETTINGS                                            \
        "bootfile=cam5200/uImage\0"                                     \
        "u-boot=cam5200/u-boot.bin\0"                                   \
-       "setup=tftp 200000 cam5200/setup.img; autoscr 200000\0"
+       "setup=tftp 200000 cam5200/setup.img; source 200000\0"
 #endif
 
 #if defined(CONFIG_TQM5200_B)
@@ -407,7 +418,9 @@
 #endif
 
 /* Dynamic MTD partition support */
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT         "nor0=TQM5200-0"
 
 #ifdef CONFIG_STK52XX
@@ -487,7 +500,7 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -507,10 +520,11 @@
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC     1
+#define CONFIG_MPC5xxx_FEC_MII100
 /*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
+ * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
  */
-/* #define CONFIG_FEC_10MBIT 1 */
+/* #define CONFIG_MPC5xxx_FEC_MII10 */
 #define CONFIG_PHY_ADDR                0x00
 
 /*
@@ -537,6 +551,8 @@
  *      101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used.
  *             Extended POST test is not available.
  *             Use for STK52xx, FO300 and CAM5200 boards.
+ *             WARNING: When the extended POST is enabled, these bits will
+ *                      be overridden by this code as GPIOs!
  * use PCI_DIS: Bit 16 (mask 0x00008000):
  *        1 -> disable PCI controller (on CAM5200 board).
  * use USB: Bits 18-19 (mask 0x00003000):
@@ -549,7 +565,7 @@
  *      000 -> All PSC2 pins are GPIOs.
  *      100 -> UART (on CAM5200 board).
  *      001 -> CAN1/2 on PSC2 pins.
- *             Use for REV100 STK52xx boards
+ *             Use for REV100 STK52xx boards
  *      01x -> Use AC97 (on FO300 board).
  * use PSC1: Bits 29-31 (mask: 0x00000007):
  *      100 -> UART (on all boards).
@@ -628,13 +644,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
 
 #define CONFIG_SYS_BOOTCS_START        CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE         CONFIG_SYS_FLASH_SIZE
@@ -708,20 +719,20 @@
 
 #define CONFIG_SYS_ATA_BASE_ADDR       MPC5XXX_ATA
 
-/* Offset for data I/O                 */
+/* Offset for data I/O */
 #define CONFIG_SYS_ATA_DATA_OFFSET     (0x0060)
 
-/* Offset for normal register accesses */
+/* Offset for normal register accesses */
 #define CONFIG_SYS_ATA_REG_OFFSET      (CONFIG_SYS_ATA_DATA_OFFSET)
 
-/* Offset for alternate registers      */
+/* Offset for alternate registers */
 #define CONFIG_SYS_ATA_ALT_OFFSET      (0x005C)
 
-/* Interval between registers                                               */
+/* Interval between registers */
 #define CONFIG_SYS_ATA_STRIDE          4
 
 /* Support ATAPI devices */
-#define CONFIG_ATAPI            1
+#define CONFIG_ATAPI                   1
 
 /*-----------------------------------------------------------------------
  * Open firmware flat tree support