#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
"protect on FC000000 +${filesize}\0"
#endif
+#ifndef CONFIG_CAM5200
+#define CUSTOM_ENV_SETTINGS \
+ "bootfile=/tftpboot/tqm5200/uImage\0" \
+ "bootfile_fdt=/tftpboot/tqm5200/uImage_fdt\0" \
+ "fdt_file=/tftpboot/tqm5200/tqm5200.dtb\0" \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0"
+#else
+#define CUSTOM_ENV_SETTINGS \
+ "bootfile=cam5200/uImage\0" \
+ "u-boot=cam5200/u-boot.bin\0" \
+ "setup=tftp 200000 cam5200/setup.img; autoscr 200000\0"
+#endif
+
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=ttyS0\0" \
+ "kernel_addr=200000\0" \
+ "fdt_addr=400000\0" \
+ "hostname=tqm5200\0" \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addcons=setenv bootargs ${bootargs} " \
- "console=ttyS0,${baudrate}\0" \
+ "console=${console},${baudrate}\0" \
"flash_self=run ramargs addip addcons;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_nfs=run nfsargs addip addcons;" \
"bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
- "bootm\0" \
- "bootfile=/tftpboot/tqm5200/uImage\0" \
- "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
+ "net_nfs=tftp ${kernel_addr} ${bootfile};" \
+ "run nfsargs addip addcons;bootm\0" \
+ "net_nfs_fdt=tftp ${kernel_addr} ${bootfile_fdt};" \
+ "tftp ${fdt_addr} ${fdt_file};setenv console ttyPSC0;" \
+ "run nfsargs addip addcons;" \
+ "bootm ${kernel_addr} - ${fdt_addr}\0" \
+ CUSTOM_ENV_SETTINGS \
"load=tftp 200000 ${u-boot}\0" \
ENV_UPDT \
""
/*
* IPB Bus clocking configuration.
*/
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-#if defined(CFG_IPBSPEED_133) && !defined(CONFIG_CAM5200)
+#if defined(CFG_IPBCLK_EQUALS_XLBCLK) && !defined(CONFIG_CAM5200)
/*
* PCI Bus clocking configuration
*
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't
- * been tested with a IPB Bus Clock of 66 MHz.
+ * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock of
+ * 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
*/
-#define CFG_PCISPEED_66 /* define for 66MHz speed */
+#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
#endif
/*
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#ifdef CFG_PCISPEED_66
+#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2
#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
#else
#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
/* Interval between registers */
#define CFG_ATA_STRIDE 4
+/*-----------------------------------------------------------------------
+ * Open firmware flat tree support
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
#endif /* __CONFIG_H */