#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG 1
-
/*
* High Level Configuration Options
* (easy to change)
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
+#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#ifdef CONFIG_STK52XX
+#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
+#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+#define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+#define CONFIG_BOARD_EARLY_INIT_R
+#endif /* CONFIG_STK52XX */
#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
/*
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
+#ifdef CONFIG_STK52XX
+#define CONFIG_PCI 1
+#elif
#define CONFIG_PCI 0
+#endif
#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
+/* #define CONFIG_PCI_SCAN_SHOW 1 */
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#define ADD_PCI_CMD 0 /* CFG_CMD_PCI */
+#ifdef CONFIG_STK52XX
+#define ADD_PCI_CMD CFG_CMD_PCI
+#elif
+#define ADD_PCI_CMD 0
+#endif
#else /* MPC5100 */
#endif
/* USB */
-#if 0
+#ifdef CONFIG_STK52XX
#define CONFIG_USB_OHCI
#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define CONFIG_DOS_PARTITION
#define CONFIG_USB_STORAGE
#else
#define ADD_USB_CMD 0
#endif
/* IDE */
-#if defined (CONFIG_MINIFAP)
+#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
#define ADD_IDE_CMD CFG_CMD_IDE | CFG_CMD_FAT
#else
#define ADD_IDE_CMD 0
"update=protect off 1:0-4; erase 1:0-4; cp.b 200000 0xfc000000 $(filesize); protect on 1:0-4\0" \
"serverip=172.20.5.13\0" \
""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk3.0_ppc/ppc_82xx\0" \
+ "bootfile=uImage_tqm5200_mkr\0" \
+ "load=tftp 200000 $(loadfile)\0" \
+ "load133=tftp 200000 $(loadfile133)\0" \
+ "loadfile=u-boot_tqm5200_mkr.bin\0" \
+ "loadfile133=u-boot_tqm5200_133_mkr.bin\0" \
+ "update=protect off fc000000 fc03ffff; erase fc000000 fc03ffff; cp.b 200000 0xfc000000 $(filesize); protect on fc000000 fc03ffff\0" \
+ "serverip=172.20.5.13\0" \
+ ""
#endif
#endif
#endif
*/
#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AC)
-#define CFG_FLASH_SIZE 0x00400000 /* 4 MByte */
-#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */
-#else
-#ifdef CONFIG_TQM5200_AB
+/* use CFI flash driver if no module variant is spezified */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START }
+#define CFG_FLASH_EMPTY_INFO
#define CFG_FLASH_SIZE 0x02000000 /* 32 MByte */
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
-#endif
-#endif
#if !defined(CFG_LOWBOOT)
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00740000 + 0x00800000)
#else /* CFG_LOWBOOT */
-#if defined(CONFIG_TQM5200_AA) || defined(CONFIG_TQM5200_AB) || \
- defined (CONFIG_TQM5200_AC)
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00040000)
-#endif
#endif /* CFG_LOWBOOT */
#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
* EEPROM
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
- * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x07000000):
- * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
+ * use PSC6:
+ * on STK52xx:
+ * use as UART. Pins PSC6_0 to PSC6_3 are used.
+ Bits 9:11 (mask: 0x00700000):
+ * 101 -> PSC6 : Extended POST test is not available
+ * on MINI-FAP and TQM5200_IB:
+ * use PSC6_1 and PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
+ * 011 -> PSC6 could not be used as UART or CODEC. IrDA still possible.
* GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
* tests.
*/
#if defined (CONFIG_MINIFAP)
-#define CFG_GPS_PORT_CONFIG 0x93000004
+#define CFG_GPS_PORT_CONFIG 0x91300004
+#elif defined (CONFIG_STK52XX)
+#define CFG_GPS_PORT_CONFIG 0x81500004
#else
-#define CFG_GPS_PORT_CONFIG 0x83000004
+#define CFG_GPS_PORT_CONFIG 0x81300004
#endif
/*
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
+/* automatic configuration of chip selects */
+#ifdef CONFIG_CS_AUTOCONF
+#define CONFIG_LAST_STAGE_INIT
+#endif
+
/*
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#ifdef CONFIG_TQM5200_AB
+#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
+#ifdef CONFIG_TQM5200_AB
#define CFG_CS2_SIZE 0x80000 /* 512 kByte */
+#else /* CONFIG_CS_AUTOCONF */
+#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
+#endif
#define CFG_CS2_CFG 0x0004D930
#endif
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC)
+#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
+ defined (CONFIG_CS_AUTOCONF)
#define CFG_CS1_START 0xE0000000
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
-#define CFG_CS1_CFG 0x0148FF70
+#define CFG_CS1_CFG 0x8F48FF70
#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000
#endif
projects / platform / kernel / u-boot.git / blobdiff