i2c: Move PPC4xx I2C driver into drivers/i2c directory

[platform/kernel/u-boot.git] / include / configs / TQM5200.h

diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index fe1d102..107bff1 100644 (file)
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -408,6 +408,8 @@
 
 /* Dynamic MTD partition support */
 #define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT         "nor0=TQM5200-0"
 
 #ifdef CONFIG_STK52XX
@@ -538,6 +540,8 @@
  *      101 -> use PSC6 as UART. Pins PSC6_0 to PSC6_3 are used.
  *             Extended POST test is not available.
  *             Use for STK52xx, FO300 and CAM5200 boards.
+ *             WARNING: When the extended POST is enabled, these bits will
+ *                      be overridden by this code as GPIOs!
  * use PCI_DIS: Bit 16 (mask 0x00008000):
  *        1 -> disable PCI controller (on CAM5200 board).
  * use USB: Bits 18-19 (mask 0x00003000):
@@ -550,7 +554,7 @@
  *      000 -> All PSC2 pins are GPIOs.
  *      100 -> UART (on CAM5200 board).
  *      001 -> CAN1/2 on PSC2 pins.
- *             Use for REV100 STK52xx boards
+ *             Use for REV100 STK52xx boards
  *      01x -> Use AC97 (on FO300 board).
  * use PSC1: Bits 29-31 (mask: 0x00000007):
  *      100 -> UART (on all boards).
@@ -629,13 +633,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
 
 #define CONFIG_SYS_BOOTCS_START        CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE         CONFIG_SYS_FLASH_SIZE
@@ -709,20 +708,20 @@
 
 #define CONFIG_SYS_ATA_BASE_ADDR       MPC5XXX_ATA
 
-/* Offset for data I/O                 */
+/* Offset for data I/O */
 #define CONFIG_SYS_ATA_DATA_OFFSET     (0x0060)
 
-/* Offset for normal register accesses */
+/* Offset for normal register accesses */
 #define CONFIG_SYS_ATA_REG_OFFSET      (CONFIG_SYS_ATA_DATA_OFFSET)
 
-/* Offset for alternate registers      */
+/* Offset for alternate registers */
 #define CONFIG_SYS_ATA_ALT_OFFSET      (0x005C)
 
-/* Interval between registers                                               */
+/* Interval between registers */
 #define CONFIG_SYS_ATA_STRIDE          4
 
 /* Support ATAPI devices */
-#define CONFIG_ATAPI            1
+#define CONFIG_ATAPI                   1
 
 /*-----------------------------------------------------------------------
  * Open firmware flat tree support