/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2014 Freescale Semiconductor, Inc.
- * Copyright 2020 NXP
+ * Copyright 2020-2021 NXP
*/
/*
#ifndef __T2080RDB_H
#define __T2080RDB_H
+#include <linux/stringify.h>
+
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_ENABLE_36BIT_PHYS
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
-
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_PAD_TO 0x40000
#define CONFIG_SPL_MAX_SIZE 0x28000
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
#endif
#ifdef CONFIG_SPIFLASH
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
#endif
#ifdef CONFIG_SDCARD
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
#endif
#endif /* CONFIG_RAMBOOT_PBL */
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-
-#if defined(CONFIG_SPIFLASH)
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#endif
-
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ 66660000
-#define CONFIG_DDR_CLK_FREQ 133330000
/*
* Config the L3 Cache as L3 SRAM
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* DDR Setup
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1 0x51
| CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define CONFIG_SYS_NAND_DDR_LAW 11
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/*
* Serial Port
/*
* I2C
*/
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
-#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
-#define CONFIG_SYS_FSL_I2C_SPEED 100000
-#define CONFIG_SYS_FSL_I2C2_SPEED 100000
-#define CONFIG_SYS_FSL_I2C3_SPEED 100000
-#define CONFIG_SYS_FSL_I2C4_SPEED 100000
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-
-#define CONFIG_SYS_I2C_FSL
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
#ifdef CONFIG_PCI
-#if !defined(CONFIG_DM_PCI)
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
* env, so we got 0x110000.
*/
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-#define CONFIG_CORTINA_FW_ADDR 0x120000
#elif defined(CONFIG_SDCARD)
/*
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0)
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
* master LAW->the ucode address in master's memory space.
*/
#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
-#define CONFIG_CORTINA_FW_ADDR 0xFFE10000
#else
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#define CONFIG_CORTINA_FW_ADDR 0xEFE00000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */
#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_CORTINA_FW_LENGTH 0x40000
#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
#define RGMII_PHY2_ADDR 0x02
#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */
#define CORTINA_PHY_ADDR2 0x0d
-#define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */
+/* Aquantia AQ1202 10G Base-T used by board revisions up to C */
+#define FM1_10GEC3_PHY_ADDR 0x00
#define FM1_10GEC4_PHY_ADDR 0x01
+/* Aquantia AQR113C 10G Base-T used by board revisions D and up */
+#define AQR113C_PHY_ADDR1 0x00
+#define AQR113C_PHY_ADDR2 0x08
#endif
#ifdef CONFIG_FMAN_ENET
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
/*
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
#define __USB_PHY_TYPE utmi
#define CONFIG_EXTRA_ENV_SETTINGS \
* For emulation this causes u-boot to jump to the start of the
* proof point app code automatically
*/
-#define CONFIG_PROOF_POINTS \
+#define PROOF_POINTS \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x29000000 - - -;" \
"cpu 7 release 0x29000000 - - -;" \
"go 0x29000000"
-#define CONFIG_HVBOOT \
+#define HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
"bootm 0x01000000 - 0x00f00000"
-#define CONFIG_ALU \
+#define ALU \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x01000000 - - -;" \
"cpu 7 release 0x01000000 - - -;" \
"go 0x01000000"
-#define CONFIG_LINUX \
+#define LINUXBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"setenv ramdiskaddr 0x02000000;" \
"setenv loadaddr 0x1000000;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_HDBOOT \
+#define HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
-#define CONFIG_NFSBOOTCOMMAND \
+#define NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
-#define CONFIG_RAMBOOTCOMMAND \
+#define RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+#define CONFIG_BOOTCOMMAND LINUXBOOTCOMMAND
#include <asm/fsl_secure_boot.h>
projects / platform / kernel / u-boot.git / blobdiff