#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
-
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_PAD_TO 0x40000
#define CONFIG_SPL_MAX_SIZE 0x28000
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
#endif
#ifdef CONFIG_SPIFLASH
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
#endif
#ifdef CONFIG_SDCARD
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
-#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
#endif
#endif /* CONFIG_RAMBOOT_PBL */
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ 66660000
-#define CONFIG_DDR_CLK_FREQ 133330000
/*
* Config the L3 Cache as L3 SRAM
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1 0x51
| CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define CONFIG_SYS_NAND_DDR_LAW 11
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/*
* Serial Port
/*
* I2C
*/
-#if !CONFIG_IS_ENABLED(DM_I2C)
-#define CONFIG_SYS_I2C_LEGACY
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
-#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
-#define CONFIG_SYS_FSL_I2C_SPEED 100000
-#define CONFIG_SYS_FSL_I2C2_SPEED 100000
-#define CONFIG_SYS_FSL_I2C3_SPEED 100000
-#define CONFIG_SYS_FSL_I2C4_SPEED 100000
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
-#endif
-
-#define CONFIG_SYS_I2C_FSL
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
*/
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-#elif defined(CONFIG_MTD_RAW_NAND)
-#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
* Slave has no ucode locally, it can fetch this from remote. When implementing
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
#define __USB_PHY_TYPE utmi
#define CONFIG_EXTRA_ENV_SETTINGS \
* For emulation this causes u-boot to jump to the start of the
* proof point app code automatically
*/
-#define CONFIG_PROOF_POINTS \
+#define PROOF_POINTS \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x29000000 - - -;" \
"cpu 7 release 0x29000000 - - -;" \
"go 0x29000000"
-#define CONFIG_HVBOOT \
+#define HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
"bootm 0x01000000 - 0x00f00000"
-#define CONFIG_ALU \
+#define ALU \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x01000000 - - -;" \
"cpu 7 release 0x01000000 - - -;" \
"go 0x01000000"
-#define CONFIG_LINUX \
+#define LINUXBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"setenv ramdiskaddr 0x02000000;" \
"setenv loadaddr 0x1000000;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_HDBOOT \
+#define HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
-#define CONFIG_NFSBOOTCOMMAND \
+#define NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
-#define CONFIG_RAMBOOTCOMMAND \
+#define RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+#define CONFIG_BOOTCOMMAND LINUXBOOTCOMMAND
#include <asm/fsl_secure_boot.h>
projects / platform / kernel / u-boot.git / blobdiff