configs: Migrate CONFIG_SYS_MAX_FLASH_BANKS to Kconfig

[platform/kernel/u-boot.git] / include / configs / T208xRDB.h

diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index fbe8852..86dc5bf 100644 (file)
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -39,7 +39,6 @@
 #define CONFIG_SYS_NAND_U_BOOT_SIZE    (768 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST     0x00200000
 #define CONFIG_SYS_NAND_U_BOOT_START   0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS    (256 << 10)
 #endif
 
 #ifdef CONFIG_SPIFLASH
@@ -89,12 +88,6 @@
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
 #endif
 
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ    66660000
-
 /*
  * Config the L3 Cache as L3 SRAM
  */
@@ -158,7 +151,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS     45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_BANKS     1       /* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT      1024    /* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
@@ -312,12 +304,6 @@ unsigned long get_board_sys_clk(void);
 
 #define I2C_MUX_CH_VOL_MONITOR 0xa
 
-#define CONFIG_VID_FLS_ENV             "t208xrdb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_IR36021_READ
 /* The lowest and highest voltage allowed for T208xRDB */
 #define VDD_MV_MIN                     819
 #define VDD_MV_MAX                     1212
@@ -372,7 +358,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_PCIE2           /* PCIE controller 2 */
 #define CONFIG_PCIE3           /* PCIE controller 3 */
 #define CONFIG_PCIE4           /* PCIE controller 4 */
-#define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT      0x80000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS      0xc00000000ull
@@ -434,35 +419,6 @@ unsigned long get_board_sys_clk(void);
 #define CONFIG_SYS_DPAA_RMAN           /* RMan */
 #define CONFIG_SYS_INTERLAKEN
 
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR                0x110000
-
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR                (512 * 0x820)
-
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR                0xFFE00000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR                0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
 #define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
 
@@ -501,7 +457,6 @@ unsigned long get_board_sys_clk(void);
  * USB
  */
 #ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_HAS_FSL_DR_USB
 #endif
@@ -596,40 +551,6 @@ unsigned long get_board_sys_clk(void);
        "cpu 7 release 0x01000000 - - -;"               \
        "go 0x01000000"
 
-#define LINUXBOOTCOMMAND                               \
-       "setenv bootargs root=/dev/ram rw "             \
-       "console=$consoledev,$baudrate $othbootargs;"   \
-       "setenv ramdiskaddr 0x02000000;"                \
-       "setenv fdtaddr 0x00c00000;"                    \
-       "setenv loadaddr 0x1000000;"                    \
-       "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define HDBOOT                                 \
-       "setenv bootargs root=/dev/$bdev rw "           \
-       "console=$consoledev,$baudrate $othbootargs;"   \
-       "tftp $loadaddr $bootfile;"                     \
-       "tftp $fdtaddr $fdtfile;"                       \
-       "bootm $loadaddr - $fdtaddr"
-
-#define NFSBOOTCOMMAND                 \
-       "setenv bootargs root=/dev/nfs rw "     \
-       "nfsroot=$serverip:$rootpath "          \
-       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-       "console=$consoledev,$baudrate $othbootargs;"   \
-       "tftp $loadaddr $bootfile;"             \
-       "tftp $fdtaddr $fdtfile;"               \
-       "bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND                         \
-       "setenv bootargs root=/dev/ram rw "             \
-       "console=$consoledev,$baudrate $othbootargs;"   \
-       "tftp $ramdiskaddr $ramdiskfile;"               \
-       "tftp $loadaddr $bootfile;"                     \
-       "tftp $fdtaddr $fdtfile;"                       \
-       "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND             LINUXBOOTCOMMAND
-
 #include <asm/fsl_secure_boot.h>
 
 #endif /* __T2080RDB_H */