#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ 66660000
-
/*
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_CS2_FTIM3 0x0
/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE 0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
| CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
#define I2C_MUX_CH_VOL_MONITOR 0xa
-#define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VOL_MONITOR_IR36021_READ
/* The lowest and highest voltage allowed for T208xRDB */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_PCIE4 /* PCIE controller 4 */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CONFIG_SYS_DPAA_RMAN /* RMan */
#define CONFIG_SYS_INTERLAKEN
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
-
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 1MB (2048 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
-
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
-#else
-#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */
* USB
*/
#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#endif
"cpu 7 release 0x01000000 - - -;" \
"go 0x01000000"
-#define LINUXBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "setenv ramdiskaddr 0x02000000;" \
- "setenv fdtaddr 0x00c00000;" \
- "setenv loadaddr 0x1000000;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define HDBOOT \
- "setenv bootargs root=/dev/$bdev rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND LINUXBOOTCOMMAND
-
#include <asm/fsl_secure_boot.h>
#endif /* __T2080RDB_H */