/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2020 NXP
*/
/*
#ifndef __T2080RDB_H
#define __T2080RDB_H
+#include <linux/stringify.h>
+
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_ENABLE_36BIT_PHYS
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_ENV_OVERWRITE
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
#define CONFIG_SPL_FLUSH_IMAGE
-#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
#define CONFIG_SPL_PAD_TO 0x40000
#define CONFIG_SPL_MAX_SIZE 0x28000
#define RESET_VECTOR_OFFSET 0x27FFC
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
-#ifdef CONFIG_NAND
+#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
-#define CONFIG_SPL_NAND_BOOT
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
-#define CONFIG_SPL_SPI_BOOT
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
-#define CONFIG_SPL_MMC_BOOT
#endif
#endif /* CONFIG_RAMBOOT_PBL */
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00400000
-
-#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
-#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (512 * 0x800)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_ADDR 0xffe20000
-#define CONFIG_ENV_SIZE 0x2000
-#elif defined(CONFIG_ENV_IS_NOWHERE)
-#define CONFIG_ENV_SIZE 0x2000
-#else
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
-#endif
-
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
#define CONFIG_SYS_L3_SIZE (512 << 10)
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
-#endif
+#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1 0x51
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-#if defined(CONFIG_NAND)
+#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
-#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
/*
* I2C
*/
+#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_SPEED 100000
#define CONFIG_SYS_FSL_I2C3_SPEED 100000
#define CONFIG_SYS_FSL_I2C4_SPEED 100000
+#else
+#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
+#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
+#endif
+
+#define CONFIG_SYS_I2C_FSL
+
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
/*
* eSPI - Enhanced SPI
*/
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_BAR
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE 0
-#endif
/*
* General PCI
#define CONFIG_PCIE2 /* PCIE controller 2 */
#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_PCIE4 /* PCIE controller 4 */
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* controller 4, Base address 203000 */
#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
-#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
-#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PCI
+#if !defined(CONFIG_DM_PCI)
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */
+#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
* env, so we got 0x110000.
*/
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
#define CONFIG_CORTINA_FW_ADDR 0x120000
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
*/
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_CORTINA_FW_IN_MMC
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
#define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_CORTINA_FW_IN_NAND
+#elif defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
* slave SRIO or PCIE outbound window->master inbound window->
* master LAW->the ucode address in master's memory space.
*/
-#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_CORTINA_FW_IN_REMOTE
#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
#define CONFIG_CORTINA_FW_ADDR 0xFFE10000
#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_CORTINA_FW_IN_NOR
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
#define CONFIG_CORTINA_FW_ADDR 0xEFE00000
#endif
#endif /* CONFIG_NOBQFMAN */
#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_AQUANTIA
-#define CONFIG_PHY_CORTINA
-#define CONFIG_PHY_REALTEK
#define CONFIG_CORTINA_FW_LENGTH 0x40000
#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
#define RGMII_PHY2_ADDR 0x02
#endif
#ifdef CONFIG_FMAN_ENET
-#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC3"
#endif
/*
* Dynamic MTD Partition support with mtdparts
*/
-#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_FLASH_CFI_MTD
-#endif
/*
* Environment