MIPS: convert CONFIG_SYS_MIPS_TIMER_FREQ to Kconfig

[platform/kernel/u-boot.git] / include / configs / T208xQDS.h

diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index eda03da..285e5fc 100644 (file)
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -21,9 +21,7 @@
 #endif
 
 /* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV   /* Category E.HV supported */
 
-#define CONFIG_SYS_FSL_CPC     /* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC     CONFIG_SYS_NUM_DDR_CTLRS
 
 #ifdef CONFIG_RAMBOOT_PBL
@@ -57,7 +55,7 @@
 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 /* Set 1M boot space */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
@@ -70,7 +68,6 @@
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-#define CONFIG_SYS_CACHE_STASHING
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
 #endif
@@ -85,10 +82,6 @@
 #define CONFIG_SYS_DCSRBAR     0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS        0xf00000000ull
 
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM      0
-
 /*
  * DDR Setup
  */
@@ -133,14 +126,8 @@
                                FTIM2_NOR_TWP(0x1c))
 #define CONFIG_SYS_NOR_FTIM3   0x0
 
-#define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS     45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_SECT      1024    /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE_PHYS \
                                        + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 
@@ -268,10 +255,6 @@
 #define CONFIG_SYS_CS2_FTIM3           CONFIG_SYS_NAND_FTIM3
 #endif
 
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
 #define CONFIG_HWCONFIG
 
 /* define to use L1 as initial stack */
@@ -368,10 +351,6 @@
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
-#define CONFIG_PCIE1           /* PCIE controller 1 */
-#define CONFIG_PCIE2           /* PCIE controller 2 */
-#define CONFIG_PCIE3           /* PCIE controller 3 */
-#define CONFIG_PCIE4           /* PCIE controller 4 */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CONFIG_SYS_PCIE1_MEM_VIRT      0x80000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS      0xc00000000ull
@@ -395,10 +374,6 @@
 #define CONFIG_SYS_PCIE4_MEM_PHYS      0xc40000000ull
 #define CONFIG_SYS_PCIE4_IO_PHYS       0xff8030000ull
 
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
-#endif
-
 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
 #define CONFIG_SYS_BMAN_NUM_PORTALS    18
@@ -432,8 +407,6 @@
 #define CONFIG_SYS_DPAA_DCE
 #define CONFIG_SYS_DPAA_RMAN           /* RMan */
 #define CONFIG_SYS_INTERLAKEN
-
-#define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
 
 #ifdef CONFIG_SYS_DPAA_FMAN
@@ -455,7 +428,6 @@
  */
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 #endif
 
 /*
@@ -478,7 +450,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 /*
  * Environment Configuration
@@ -495,7 +466,7 @@
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
-       "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
+       "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
        "tftpflash=tftpboot $loadaddr $uboot && "               \
        "protect off $ubootaddr +$filesize && "                 \
        "erase $ubootaddr +$filesize && "                       \