global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace

[platform/kernel/u-boot.git] / include / configs / T104xRDB.h

diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 365640d..ad8037e 100644 (file)
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -58,13 +58,11 @@
 #define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
 #endif
 
-#define CONFIG_SYS_FSL_CPC             /* Corenet Platform Cache */
 #define CONFIG_SYS_NUM_CPC             CONFIG_SYS_NUM_DDR_CTLRS
 
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-#define CONFIG_SYS_CACHE_STASHING
 #define CONFIG_SYS_INIT_L2CSR0         L2CSR0_L2E
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
@@ -80,7 +78,6 @@
  * (CONFIG_SYS_INIT_L3_VADDR) will be different.
  */
 #define CONFIG_SYS_INIT_L3_VADDR       0xFFFC0000
-#define CONFIG_SYS_L3_SIZE             256 << 10
 #define SPL_ENV_ADDR                   (CONFIG_SPL_GD_ADDR + 4 * 1024)
 
 #define CONFIG_SYS_DCSRBAR             0xf0000000
@@ -129,14 +126,8 @@
                                FTIM2_NOR_TWP(0x1c))
 #define CONFIG_SYS_NOR_FTIM3   0x0
 
-#define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS     45 /* count down from 45/5: 9..1 */
 
-#define CONFIG_SYS_MAX_FLASH_SECT      1024    /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE_PHYS}
 
 /* CPLD on IFC */
@@ -221,7 +212,6 @@
 
 #define CONFIG_SYS_NAND_DDR_LAW                11
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
 
 #if defined(CONFIG_MTD_RAW_NAND)
 #define CONFIG_SYS_CSPR0_EXT           CONFIG_SYS_NAND_CSPR_EXT
@@ -263,7 +253,6 @@
 
 /* define to use L1 as initial stack */
 #define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000      /* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe03c000
@@ -275,8 +264,6 @@
 
 #define CONFIG_SYS_INIT_SP_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
-#define CONFIG_SYS_MONITOR_LEN         (768 * 1024)
-
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
@@ -300,11 +287,6 @@
 #if defined(CONFIG_TARGET_T1042RDB_PI) || \
        defined(CONFIG_TARGET_T1040D4RDB)       || \
        defined(CONFIG_TARGET_T1042D4RDB)
-/* LDI/DVI Encoder for display */
-#define CONFIG_SYS_I2C_LDI_ADDR                0x38
-#define CONFIG_SYS_I2C_DVI_ADDR                0x75
-#define CONFIG_SYS_I2C_DVI_BUS_NUM     0
-
 /*
  * RTC configuration
  */
@@ -364,7 +346,7 @@
 */
 
 #ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CFG_SYS_FSL_ESDHC_ADDR       CFG_SYS_MPC85xx_ESDHC_ADDR
 #endif
 
 /* Qman/Bman */
@@ -396,8 +378,6 @@
 
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_DPAA_PME
-
-#define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
 
 #ifdef CONFIG_FMAN_ENET
@@ -433,12 +413,6 @@
 #endif
 
 /*
- * Environment
- */
-#define CONFIG_LOADS_ECHO              /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
-
-/*
  * Miscellaneous configurable options
  */
 
@@ -448,7 +422,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 /*
  * Dynamic MTD Partition support with mtdparts
@@ -481,7 +454,7 @@
        "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
-       "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
+       "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
        "tftpflash=tftpboot $loadaddr $uboot && "               \
        "protect off $ubootaddr +$filesize && "                 \
        "erase $ubootaddr +$filesize && "                       \