#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_MP /* support multiple processors */
-#define CONFIG_PHYS_64BIT
#define CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_BOARD_EARLY_INIT_F
#endif
+#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
+
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_rcw.cfg
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
-
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
/* Video */
#ifdef CONFIG_PPC_T1024 /* no DIU on T1023 */
#define CONFIG_FSL_DIU_FB
#endif
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
/*
* eSPI - Enhanced SPI
*/
-#define CONFIG_SPI_FLASH_STMICRO
#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_EON
#endif
-#define CONFIG_CMD_SF
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CONFIG_PCI /* Enable PCI/PCIE */
-#define CONFIG_PCIE1 /* PCIE controler 1 */
-#define CONFIG_PCIE2 /* PCIE controler 2 */
-#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE2 /* PCIE controller 2 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
#endif
/*
#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
#endif
/*
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
* Command line configuration.
*/
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#ifdef CONFIG_PCI
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define __USB_PHY_TYPE utmi
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
#define CONFIG_BOOTCOMMAND CONFIG_LINUX
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
+/* Hash command with SHA acceleration supported in hardware */
+#ifdef CONFIG_FSL_CAAM
+#define CONFIG_CMD_HASH
+#define CONFIG_SHA_HW_ACCEL
#endif
+#include <asm/fsl_secure_boot.h>
+
#endif /* __T1024QDS_H */