#ifndef _CONFIG_SBX81LIFXCAT_H
#define _CONFIG_SBX81LIFXCAT_H
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
-#define CONFIG_KW88F6281 1 /* SOC Name */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
-
/* additions for new ARM relocation support */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_GPIO 1
+#define CFG_SYS_SDRAM_BASE 0x00000000
/*
* NS16550 Configuration
*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+#define CFG_SYS_NS16550_CLK CFG_SYS_TCLK
+#define CFG_SYS_NS16550_COM1 KW_UART0_BASE
/*
* Serial Port configuration
* for your console driver.
*/
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
-#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
#define MTDPARTS_MTDOOPS "errlog"
-#define CONFIG_DOS_PARTITION
/*
* Environment variables configurations
*/
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
-#define CONFIG_ENV_SIZE 0x02000
-#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
/*
* U-Boot bootcode configuration
*/
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
-#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
/* size in bytes reserved for initial data */
#include <asm/arch/config.h>
/* There is no PHY directly connected so don't ask it for link status */
-#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
#define CONFIG_PHY_BASE_ADR 0x01
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
#endif /* CONFIG_CMD_NET */
-#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
-
#endif /* _CONFIG_SBX81LIFXCAT_H */