* MA 02111-1307 USA
*/
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+/*
+ * sbc8540 board configuration file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#if XXX
-#define DEBUG /* General debug */
-#define ET_DEBUG
+/*
+ * Top level Makefile configuration choices
+ */
+#ifdef CONFIG_66
+#define CONFIG_PCI_66
#endif
+
#define TSEC_DEBUG
-/* High Level Configuration Options */
+/*
+ * High Level Configuration Options
+ */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
+#define CONFIG_SYS_TEXT_BASE 0xfffc0000
+
#define CONFIG_CPM2 1 /* has CPM2 */
/* below can be toggled for performance analysis. otherwise use default */
#define CONFIG_L2_CACHE /* toggle L2 cache */
#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
#endif
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-
-#if XXX
- #define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#else
- #define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-
#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
/* DDR Setup */
#undef CONFIG_DDR_SPD
#if defined(CONFIG_MPC85xx_REV1)
- #define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */
#endif
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#undef CONFIG_CONS_NONE /* define if console on something else */
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-# define CONFIG_NET_MULTI 1
# define CONFIG_MPC85xx_TSEC1
# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
# define CONFIG_MII 1 /* MII PHY management */
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
#define CONFIG_SYS_CPMFCR_RAMTYPE 0
#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
* GPIO pins used for bit-banged MII communications
*/
#define MDIO_PORT 2 /* Port C */
+ #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
+ (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+ #define MDC_DECLARE MDIO_DECLARE
+
#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#if 0
/* XXX This doesn't work and I don't want to fix it */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#define CONFIG_GATEWAYIP YourGatewayIP
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_HOSTNAME SBC8560
-#define CONFIG_ROOTPATH YourRootPath
-#define CONFIG_BOOTFILE YourImageName
+#define CONFIG_ROOTPATH "YourRootPath"
+#define CONFIG_BOOTFILE "YourImageName"
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff