#define CONFIG_RATTLER /* Analogue&Micro Rattler board */
-#undef DEBUG
-
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
#define CONFIG_ENV_OVERWRITE
* SCC, 1-3 for FCC)
*
* If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CFG_CMD_NET must
- * be removed from CONFIG_COMMANDS to remove support for networking.
+ * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
+ * must be unset.
*/
#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
#define CONFIG_BAUDRATE 38400
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_DHCP \
- | CFG_CMD_IMMAP \
- | CFG_CMD_JFFS2 \
- | CFG_CMD_MII \
- | CFG_CMD_PING \
- )
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_IMMAP
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOOTCOMMAND "bootm FE040000" /* autoboot command */
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rw mtdparts=phys:1M(ROM)ro,-(root)"
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
#define CFG_PROMPT_HUSH_PS2 "> "
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_FLASH_BASE 0xFE000000
#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CFG_DIRECT_FLASH_TFTP
-#if (CONFIG_COMMANDS & CFG_CMD_JFFS2)
+#if defined(CONFIG_CMD_JFFS2)
#define CFG_JFFS2_NUM_BANKS CFG_MAX_FLASH_BANKS
#define CFG_JFFS2_SORT_FRAGMENTS
#define MTDIDS_DEFAULT "nor0=rattler-0"
#define MTDPARTS_DEFAULT "mtdparts=rattler-0:-@1m(jffs2)"
*/
-#endif /* CFG_CMD_JFFS2 */
+#endif /* CONFIG_CMD_JFFS2 */
#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_IS_IN_FLASH
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-#endif /* CFG_ENV_IS_IN_FLASH */
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
#define CFG_DEFAULT_IMMR 0xFF010000
/* Hard reset configuration word */
#define CFG_HRCW_MASTER 0x0A06875A /* Not used - provided by FPGA */
/* No slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif