#define CONFIG_SYS_TEXT_BASE 0xFFF90000
#endif
-#define CONFIG_DISPLAY_BOARDINFO
-
#define CONFIG_SYS_CLK_FREQ 33333400
#if 0 /* temporary disabled because OS/9 does not like dcache on startup */
#define CONFIG_4xx_DCACHE /* enable dcache */
#endif
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_F 1
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_TYPES 1 /* support board types */
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
-/*
- * standard dtt sensor configuration - bottom bit will determine local or
- * remote sensor of the TMP401
- */
-#define CONFIG_DTT_SENSORS { 0, 1 }
-
-/*
- * The PMC440 uses a TI TMP401 temperature sensor. This part
- * is basically compatible to the ADM1021 that is supported
- * by U-Boot.
- *
- * - i2c addr 0x4c
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT ouput disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
- */
-#define CONFIG_DTT_ADM1021
-#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
-
#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \
"\\\"painit\\\" to preboot command"
"cp.b 200000 fff90000 70000\0" \
""
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/* USB */
#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1
#define USB_2_0_DEVICE
/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_MII
+
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_REGINFO
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-
#define CONFIG_SUPPORT_VFAT
/*-----------------------------------------------------------------------
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
-#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
-#define CONFIG_API 1
-
#endif /* __CONFIG_H */