#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_NET_MULTI 1
+#undef CONFIG_HAS_ETH1
+
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_UNIVERSE
+#define CONFIG_CMD_EEPROM
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_BSP | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_ELF | \
- CFG_CMD_DATE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_I2C | \
- CFG_CMD_PING | \
- CFG_CMD_UNIVERSE | \
- CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
+#define CFG_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408 /* PCI Device ID: Non-Monarch */
+#define CFG_PCI_SUBSYS_DEVICEID_MONARCH 0x0409 /* PCI Device ID: Monarch */
+#define CFG_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid()
+
#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+
+#define CFG_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
+#define CFG_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#if 1
+#define CFG_PCI_PTM2LA 0xef000000 /* point to internal regs */
+#define CFG_PCI_PTM2MS 0xff000001 /* 16MB, enable */
+#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+#else /* old mapping */
#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
+#endif
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_BASE 0xFE000000
#define CFG_FLASH_INCREMENT 0x01000000
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_PROTECTION 1 /* don't use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT }
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*
/* No command line, one static partition, whole device */
#undef CONFIG_JFFS2_CMDLINE
#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
+#define CONFIG_JFFS2_PART_SIZE 0x01b00000
+#define CONFIG_JFFS2_PART_OFFSET 0x00400000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
/* total size of a CAT24WC16 is 2048 bytes */
#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
#define CAN_BA 0xF0000000 /* CAN Base Address */
#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define NVRAM_BA 0xF0200000 /* NVRAM Base Address */
/* Memory Bank 0 (Flash Bank 0) initialization */
#define CFG_EBC_PB0AP 0x92015480
#define CFG_EBC_PB2AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
-#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 -> unused */
+
+/* Memory Bank 4 (NVRAM) initialization */
+#define CFG_EBC_PB4AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CFG_EBC_PB4CR NVRAM_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* FPGA stuff
#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
/*-----------------------------------------------------------------------
+ * GPIOs
+ */
+#define CFG_NONMONARCH (0x80000000 >> 14) /* GPIO24 */
+#define CFG_XEREADY (0x80000000 >> 15) /* GPIO15 */
+#define CFG_INTA_FAKE (0x80000000 >> 19) /* GPIO19 */
+#define CFG_SELF_RST (0x80000000 >> 21) /* GPIO21 */
+#define CFG_REV1_2 (0x80000000 >> 23) /* GPIO23 */
+
+/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
projects / platform / kernel / u-boot.git / blobdiff