/*
- * (C) Copyright 2001-2003
+ * (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_NET_MULTI 1
+#undef CONFIG_HAS_ETH1
+
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_UNIVERSE
+#define CONFIG_CMD_EEPROM
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_BSP | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
- CFG_CMD_ELF | \
- CFG_CMD_DATE | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_I2C | \
- CFG_CMD_PING | \
- CFG_CMD_EEPROM )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000300 /* RTC Base Address */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID_NONMONARCH 0x0408 /* PCI Device ID: Non-Monarch */
+#define CFG_PCI_SUBSYS_DEVICEID_MONARCH 0x0409 /* PCI Device ID: Monarch */
+#define CFG_PCI_SUBSYS_DEVICEID pmc405_pci_subsys_deviceid()
+
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+
+#define CFG_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
+#define CFG_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#if 1
+#define CFG_PCI_PTM2LA 0xef000000 /* point to internal regs */
+#define CFG_PCI_PTM2MS 0xff000001 /* 16MB, enable */
+#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
+#else /* old mapping */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#endif
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_BASE 0xFE000000
#define CFG_FLASH_INCREMENT 0x01000000
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_PROTECTION 1 /* don't use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_MAX_FLASH_BANKS 2 /* max num of flash banks */
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, CFG_FLASH_BASE + CFG_FLASH_INCREMENT }
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+/*
+ * JFFS2 partitions - second bank contains u-boot
+ *
+ */
+/* No command line, one static partition, whole device */
+#undef CONFIG_JFFS2_CMDLINE
+#define CONFIG_JFFS2_DEV "nor0"
+#define CONFIG_JFFS2_PART_SIZE 0x01b00000
+#define CONFIG_JFFS2_PART_OFFSET 0x00400000
+
+/* mtdparts command line support */
+/* Note: fake mtd_id used, no linux mtd map file */
+/*
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT "nor0=pmc405-0"
+#define MTDPARTS_DEFAULT "mtdparts=pmc405-0:-(jffs2)"
+*/
/*-----------------------------------------------------------------------
* Environment Variable setup
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For IBM 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
#define CAN_BA 0xF0000000 /* CAN Base Address */
#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define NVRAM_BA 0xF0200000 /* NVRAM Base Address */
/* Memory Bank 0 (Flash Bank 0) initialization */
#define CFG_EBC_PB0AP 0x92015480
#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
/* Memory Bank 2 (CAN0, 1, RTC) initialization */
-#define CFG_EBC_PB2AP 0x03000040 /* TWT=6,TH=0,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CFG_EBC_PB2AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
#define CFG_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
-/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */
-#define CFG_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 -> unused */
+
+/* Memory Bank 4 (NVRAM) initialization */
+#define CFG_EBC_PB4AP 0x03000440 /* TWT=5,TH=2,CSN=0,OEN=0,WBN=0,WBF=0 */
+#define CFG_EBC_PB4CR NVRAM_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* FPGA stuff
#define CFG_FPGA_INIT 0x00010000 /* unused (ppc input) */
#define CFG_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+
+/*-----------------------------------------------------------------------
+ * GPIOs
+ */
+#define CFG_NONMONARCH (0x80000000 >> 14) /* GPIO24 */
+#define CFG_XEREADY (0x80000000 >> 15) /* GPIO15 */
+#define CFG_INTA_FAKE (0x80000000 >> 19) /* GPIO19 */
+#define CFG_SELF_RST (0x80000000 >> 21) /* GPIO21 */
+#define CFG_REV1_2 (0x80000000 >> 23) /* GPIO23 */
+
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
projects / platform / kernel / u-boot.git / blobdiff