Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE

[platform/kernel/u-boot.git] / include / configs / PM520.h

diff --git a/include/configs/PM520.h b/include/configs/PM520.h
index ff73ef9..f039e5a 100644 (file)
--- a/include/configs/PM520.h
+++ b/include/configs/PM520.h
@@ -33,13 +33,12 @@
 #define CONFIG_MPC5xxx         1       /* This is an MPC5xxx CPU */
 #define CONFIG_PM520           1       /* ... on PM520 board */
 
+#define        CONFIG_SYS_TEXT_BASE    0xfff00000
+
 #define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33MHz */
 
 #define CONFIG_MISC_INIT_R
 
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH  */
-#define BOOTFLAG_WARM          0x02    /* Software reboot           */
-
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
 
 /*
@@ -50,7 +49,6 @@
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 
-#ifdef CONFIG_MPC5200  /* MPC5100 PCI is not supported yet. */
 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
@@ -75,7 +73,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER       8  /* use 8 rx buffer on eepro100  */
 #undef  CONFIG_NS8382X
 
-#endif
 
 /* Partitions */
 #define CONFIG_DOS_PARTITION
@@ -86,12 +83,6 @@
 #define CONFIG_USB_STORAGE
 #endif
 
-#if !defined(CONFIG_BOOT_ROM)
-/* DoC requires legacy NAND for now */
-#define CONFIG_NAND_LEGACY
-#endif
-
-
 /*
  * BOOTP options
  */
@@ -117,13 +108,7 @@
 #define CONFIG_CMD_SNTP
 #define CONFIG_CMD_USB
 
-#if !defined(CONFIG_BOOT_ROM)
-#define CONFIG_CMD_DOC
-#endif
-
-#if defined(CONFIG_MPC5200)
 #define CONFIG_CMD_PCI
-#endif
 
 
 /*
@@ -157,12 +142,10 @@
 
 #define CONFIG_BOOTCOMMAND     "run flash_self"
 
-#if defined(CONFIG_MPC5200)
 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK         /* define for 133MHz speed */
-#endif
 /*
  * I2C configuration
  */
@@ -186,15 +169,6 @@
 #define CONFIG_RTC_PCF8563
 #define CONFIG_SYS_I2C_RTC_ADDR                0x51
 
-/*
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
 #define CONFIG_SYS_DOC_BASE            0xE0000000
 #define CONFIG_SYS_DOC_SIZE            0x00100000
 
@@ -259,14 +233,14 @@
 
 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_END        MPC5XXX_SRAM_SIZE       /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 
 
 #define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_BASE    TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT          1
 #endif
@@ -320,13 +294,8 @@
 /*
  * Various low-level settings
  */
-#if defined(CONFIG_MPC5200)
 #define CONFIG_SYS_HID0_INIT           HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL          HID0_ICE
-#else
-#define CONFIG_SYS_HID0_INIT           0
-#define CONFIG_SYS_HID0_FINAL          0
-#endif
 
 #if defined(CONFIG_BOOT_ROM)
 #define CONFIG_SYS_BOOTCS_START        CONFIG_SYS_BOOTROM_BASE