Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references

[platform/kernel/u-boot.git] / include / configs / PIP405.h

diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h
index 0a2d7d7..6e8d7ad 100644 (file)
--- a/include/configs/PIP405.h
+++ b/include/configs/PIP405.h
@@ -42,6 +42,15 @@
 
 
 /*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
@@ -68,7 +77,7 @@
 #define CONFIG_CMD_BSP
 
 
-#define CFG_NAND_LEGACY
+#define CONFIG_NAND_LEGACY
 
 #define         CFG_HUSH_PARSER
 #define         CFG_PROMPT_HUSH_PS2 "> "
@@ -86,15 +95,14 @@
 
 #define CFG_I2C_EEPROM_ADDR    0x53
 #define CFG_I2C_EEPROM_ADDR_LEN        2
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x800   /* 2 kBytes may be used for env vars */
+#define CONFIG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE            0x800   /* 2 kBytes may be used for env vars */
 
 #undef CFG_I2C_EEPROM_ADDR_OVERFLOW
 #define CFG_EEPROM_PAGE_WRITE_BITS 6   /* The Atmel 24C128/256 has     */
                                        /* 64 byte page write mode using*/
                                        /* last 6 bits of the address   */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE   /* enable Page write */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10      /* and takes up to 10 msec */
 
 
@@ -114,7 +122,7 @@
 #define CONFIG_BOOTDELAY       5
 /* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
 /* #define CONFIG_BOOT_RETRY_TIME      -10     /XXX* feature is available but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK    /* check console even if bootdelay = 0 */
+#define CONFIG_ZERO_BOOTDELAY_CHECK    /* check console even if bootdelay = 0 */
 
 
 #define CONFIG_BOOTCOMMAND     "diskboot 400000 0:1; bootm" /* autoboot command                */
@@ -222,15 +230,6 @@
 #define CFG_FLASH_ERASE_TOUT   120000  /* Timeout for Flash Erase (in ms)      */
 #define CFG_FLASH_WRITE_TOUT   500     /* Timeout for Flash Write (in ms)      */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE                8192    /* For AMCC 405 CPUs                    */
-#define CFG_CACHELINE_SIZE     32      /* ...                  */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT    5       /* log base 2 of the above value        */
-#endif
-
 /*
  * Init Memory Controller:
  */
@@ -252,7 +251,7 @@
 #define CFG_TEMP_STACK_OCM     1
 #define CFG_OCM_DATA_ADDR      0xF0000000
 #define CFG_OCM_DATA_SIZE      0x1000
-#define CFG_INIT_RAM_ADDR      CFG_OCM_DATA_ADDR       /* inside of On Chip SRAM    */
+#define CFG_INIT_RAM_ADDR      CFG_OCM_DATA_ADDR       /* inside of On Chip SRAM    */
 #define CFG_INIT_RAM_END       CFG_OCM_DATA_SIZE       /* End of On Chip SRAM         */
 #define CFG_GBL_DATA_SIZE      64              /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -281,7 +280,6 @@
  ***********************************************************/
 #define CONFIG_MII             1       /* MII PHY management           */
 #define CONFIG_PHY_ADDR                1       /* PHY address                  */
-#define CONFIG_CS8952_PHY      1       /* its a CS8952 PHY             */
 /************************************************************
  * RTC
  ***********************************************************/