*/
#define CONFIG_MPC555 1 /* This is an MPC555 CPU */
-#define CONFIG_PATI 1 /* ...On a PATI board */
+#define CONFIG_PATI 1 /* ...On a PATI board */
/* Serial Console Configuration */
#define CONFIG_5xx_CONS_SCI1
#undef CONFIG_5xx_CONS_SCI2
#define CONFIG_BAUDRATE 9600
-#define CONFIG_COMMANDS (CFG_CMD_MEMORY | CFG_CMD_LOADB | CFG_CMD_REGINFO | \
- CFG_CMD_FLASH | CFG_CMD_LOADS | CFG_CMD_ENV | CFG_CMD_REGINFO | \
- CFG_CMD_BDI | CFG_CMD_CONSOLE | CFG_CMD_RUN | CFG_CMD_BSP | \
- CFG_CMD_IMI | CFG_CMD_EEPROM | CFG_CMD_IRQ | CFG_CMD_MISC \
-)
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+#define CONFIG_CMD_CONSOLE
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MISC
+
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
-#define CONFIG_BOOTCOMMAND "" /* autoboot command */
+#define CONFIG_BOOTCOMMAND "" /* autoboot command */
#define CONFIG_BOOTARGS "" /* */
-#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
+#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
-/*#define CONFIG_STATUS_LED 1 *//* Enable status led */
+/*#define CONFIG_STATUS_LED 1 */ /* Enable status led */
#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "pati=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/*
* Internal Memory Mapped (This is not the IMMR content)
*/
-#define CFG_IMMR 0x01C00000 /* Physical start adress of internal memory map */
+#define CFG_IMMR 0x01C00000 /* Physical start adress of internal memory map */
/*
* Definitions for initial stack pointer and data area
*/
-#define CFG_INIT_RAM_ADDR (CFG_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
-#define CFG_INIT_RAM_END (CFG_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
-#define CFG_GBL_DATA_SIZE 128 /* Size in bytes reserved for initial global data */
+#define CFG_INIT_RAM_ADDR (CFG_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
+#define CFG_INIT_RAM_END (CFG_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
+#define CFG_GBL_DATA_SIZE 128 /* Size in bytes reserved for initial global data */
#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_INIT_RAM_ADDR) - CFG_GBL_DATA_SIZE) /* Offset from the beginning of ram */
-#define CFG_INIT_SP_ADDR (CFG_IMMR + 0x03fa000) /* Physical start adress of inital stack */
+#define CFG_INIT_SP_ADDR (CFG_IMMR + 0x03fa000) /* Physical start adress of inital stack */
/*
* Start addresses for the final memory configuration
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
+#define CFG_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
#define CFG_FLASH_BASE 0xffC00000 /* External flash */
#define PCI_BASE 0x03000000 /* PCI Base (CS2) */
#define PCI_CONFIG_BASE 0x04000000 /* PCI & PLD (CS3) */
#define PLD_CONFIG_BASE 0x04001000 /* PLD (CS3) */
#define CFG_MONITOR_BASE 0xFFF00000
-/* CFG_FLASH_BASE */ /* TEXT_BASE is defined in the board config.mk file. */
- /* This adress is given to the linker with -Ttext to */
- /* locate the text section at this adress. */
+/* CFG_FLASH_BASE */ /* TEXT_BASE is defined in the board config.mk file. */
+ /* This adress is given to the linker with -Ttext to */
+ /* locate the text section at this adress. */
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 192 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-
#define CFG_RESET_ADDRESS (PLD_CONFIG_BASE + 0x10) /* Adress which causes reset */
/*
*/
#define CFG_MAX_FLASH_BANKS 1 /* Max number of memory banks */
-#define CFG_MAX_FLASH_SECT 128 /* Max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
+#define CFG_MAX_FLASH_SECT 128 /* Max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_EEPROM
-#ifdef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_OFFSET 0
-#define CFG_ENV_SIZE 2048
+#define CONFIG_ENV_IS_IN_EEPROM
+#ifdef CONFIG_ENV_IS_IN_EEPROM
+#define CONFIG_ENV_OFFSET 0
+#define CONFIG_ENV_SIZE 2048
#endif
-#undef CFG_ENV_IS_IN_FLASH
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SIZE 0x00002000 /* Set whole sector as env */
-#define CFG_ENV_OFFSET ((0 - CFG_FLASH_BASE) - CFG_ENV_SIZE) /* Environment starts at this adress */
+#undef CONFIG_ENV_IS_IN_FLASH
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SIZE 0x00002000 /* Set whole sector as env */
+#define CONFIG_ENV_OFFSET ((0 - CFG_FLASH_BASE) - CONFIG_ENV_SIZE) /* Environment starts at this adress */
#endif
SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
-
-
-
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control
*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* Data show cycle
*/
-#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register
* Set all bits to 40 Mhz
*
*/
-#define CFG_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
+#define CFG_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
#define CFG_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0)
*-----------------------------------------------------------------------
*
*/
-#define CFG_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
+#define CFG_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
/*-----------------------------------------------------------------------
* ICTRL - I-Bus Support Control Register
*/
-#define CFG_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
+#define CFG_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
/*-----------------------------------------------------------------------
* USIU - Memory Controller Register