hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

[platform/kernel/u-boot.git] / include / configs / P2020DS.h

diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 47f1f18..d7d64d2 100644 (file)
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -40,6 +40,13 @@
 #define CONFIG_RESET_VECTOR_ADDRESS    0xf8fffffc
 #endif
 
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE           0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS    0xf8fffffc
+#endif
+
 /* High Level Configuration Options */
 #define CONFIG_BOOKE           1       /* BOOKE */
 #define CONFIG_E500            1       /* BOOKE e500 family */
@@ -111,18 +118,8 @@
 #define CONFIG_SYS_L2_SIZE             (512 << 10)
 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xffe00000      /* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS                0xfffe00000ull  /* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#endif
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
@@ -383,9 +380,6 @@
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
 
 /*
  * Pass open firmware flat tree
@@ -418,6 +412,18 @@
 #define CONFIG_SYS_EEPROM_BUS_NUM      0
 
 /*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED                10000000
+#define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
+
+/*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
@@ -519,7 +525,6 @@
 #endif
 #define CONFIG_SYS_SRIO2_MEM_SIZE      0x20000000      /* 512M */
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -549,10 +554,6 @@
 
 #if defined(CONFIG_TSEC_ENET)
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
 #define CONFIG_TSEC1   1
@@ -592,8 +593,18 @@
  */
 #if defined(CONFIG_SDCARD)
 #define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
 #define CONFIG_ENV_SIZE                        0x2000
 #define CONFIG_SYS_MMC_ENV_DEV         0
+#elif defined(CONFIG_SPIFLASH)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS             0
+#define CONFIG_ENV_SPI_CS              0
+#define CONFIG_ENV_SPI_MAX_HZ          10000000
+#define CONFIG_ENV_SPI_MODE            0
+#define CONFIG_ENV_SIZE                        0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET              0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE           0x10000
 #else
 #define CONFIG_ENV_IS_IN_FLASH 1
 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
@@ -681,11 +692,11 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -706,8 +717,8 @@
 #define CONFIG_IPADDR          192.168.1.254
 
 #define CONFIG_HOSTNAME                unknown
-#define CONFIG_ROOTPATH                /opt/nfsroot
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/opt/nfsroot"
+#define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       u-boot.bin      /* U-Boot image on TFTP server */
 
 #define CONFIG_SERVERIP                192.168.1.1
@@ -724,7 +735,8 @@
 
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
  "perf_mode=performance\0"                     \
- "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1\0"       \
+       "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;"  \
+       "usb1:dr_mode=host,phy_type=ulpi\0"                     \
  "netdev=eth0\0"                                               \
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                                \
  "tftpflash=tftpboot $loadaddr $uboot; "                       \