+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2013 Freescale Semiconductor, Inc.
*
* Authors: Roy Zang <tie-fei.zang@freescale.com>
* Chunhe Lan <Chunhe.Lan@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
#endif
/* High Level Configuration Options */
-#define CONFIG_BOOKE /* BOOKE */
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_P1023
-#define CONFIG_MP /* support multiple processors */
-#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
-#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
-#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
+#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
+#define CONFIG_PCIE3 /* PCIE controller 3 (slot 3) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW /* Use common FSL init code */
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x02000000
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
/* Implement conversion of addresses in the LBC */
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_DDR_SPD
-#define CONFIG_SYS_FSL_DDR3
-#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x50
| BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
/* Serial Port */
-#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
*/
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
#endif
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
/* Qman/Bman */
-#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
/* For FM */
#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_FMAN_ENET
#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2
#define CONFIG_SYS_TBIPA_VALUE 8
-#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC1"
#endif
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
- "fdtaddr=c00000\0" \
+ "fdtaddr=1e00000\0" \
"fdtfile=p1023rdb.dtb\0" \
"othbootargs=ramdisk_size=600000\0" \
"bdev=sda1\0" \