hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

[platform/kernel/u-boot.git] / include / configs / P1022DS.h

diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index e9622e7..920edad 100644 (file)
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -43,8 +43,9 @@
 #define CONFIG_FSL_PCIE_RESET          /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
 
-#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
 #define CONFIG_ADDR_MAP
 #define CONFIG_SYS_NUM_ADDR_MAP                16      /* number of TLB1 entries */
 #endif
@@ -64,18 +65,8 @@
 #define CONFIG_SYS_MEMTEST_START       0x00000000
 #define CONFIG_SYS_MEMTEST_END         0x7fffffff
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xffe00000      /* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS                0xfffe00000ull
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS                CONFIG_SYS_CCSRBAR
-#endif
-#define CONFIG_SYS_IMMR                        CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR             0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_DDR_SPD
@@ -170,6 +161,8 @@
 #define PIXIS_LBMAP_SWITCH     7
 #define PIXIS_LBMAP_MASK       0xF0
 #define PIXIS_LBMAP_ALTBANK    0x20
+#define PIXIS_ELBC_SPI_MASK    0xc0
+#define PIXIS_SPI              0x80
 
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0xffd00000 /* Initial L1 address */
@@ -180,7 +173,7 @@
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN          (6 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN          (10 * 1024 * 1024)
 
 /*
  * Serial Port
@@ -199,7 +192,6 @@
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 
 /* Video */
 #define CONFIG_FSL_DIU_FB
@@ -269,6 +261,19 @@
 #define CONFIG_SYS_EEPROM_BUS_NUM      1
 
 /*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED                10000000
+#define CONFIG_SF_DEFAULT_MODE         0
+
+/*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */
@@ -331,7 +336,6 @@
 #define CONFIG_SYS_PCIE3_IO_SIZE       0x00010000      /* 64k */
 
 #ifdef CONFIG_PCI
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 #define CONFIG_E1000                   /* Define e1000 pci Ethernet card */
@@ -340,7 +344,6 @@
 /* SATA */
 #define CONFIG_LIBATA
 #define CONFIG_FSL_SATA
-#define CONFIG_FSL_SATA_V2
 
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_SATA1
@@ -375,7 +378,6 @@
 #ifdef CONFIG_TSEC_ENET
 
 #define CONFIG_TSECV2
-#define CONFIG_NET_MULTI
 
 #define CONFIG_MII                     /* MII PHY management */
 #define CONFIG_TSEC1           1
@@ -462,11 +464,11 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #ifdef CONFIG_CMD_KGDB
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -478,8 +480,8 @@
  */
 
 #define CONFIG_HOSTNAME                p1022ds
-#define CONFIG_ROOTPATH                /opt/nfsroot
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/opt/nfsroot"
+#define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       u-boot.bin      /* U-Boot image on TFTP server */
 
 #define CONFIG_LOADADDR                1000000