#include <asm/config_mpc85xx.h>
#ifdef CONFIG_SDCARD
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_MMC_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
#else
-#define CONFIG_SPL_SPI_FLASH_MINIMAL
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (512 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (96 << 10)
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SPL_COMMON_INIT_DDR
-#endif
#endif
#endif
#ifdef CONFIG_MTD_RAW_NAND
#ifdef CONFIG_NXP_ESBC
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-
-#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
-#define CONFIG_SPL_RELOC_STACK 0x00100000
#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
#else
#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SPL_NAND_INIT
-#define CONFIG_SPL_COMMON_INIT_DDR
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0xD0000000
#define CONFIG_SYS_NAND_U_BOOT_START 0xD0000000
-#else
-#ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
-#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#endif
-#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#endif
#endif
#ifdef CONFIG_NAND_SECBOOT /* NAND Boot */
-#define CONFIG_RAMBOOT_NAND
#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
#endif
/* High Level Configuration Options */
#if defined(CONFIG_PCI)
-#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
-
/*
* PCI Windows
* Memory space is mapped 1-1, but I/O space must start from 0.
#else
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
#define CONFIG_HWCONFIG
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
/* DDR Setup */
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-/* DDR3 Controller Settings */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
-#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
-#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
-#define CONFIG_SYS_DDR_RCW_1 0x00000000
-#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xc70c0008 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
-#define CONFIG_SYS_DDR_TIMING_4 0x00000001
-#define CONFIG_SYS_DDR_TIMING_5 0x03402400
-
-#define CONFIG_SYS_DDR_TIMING_3_800 0x00030000
-#define CONFIG_SYS_DDR_TIMING_0_800 0x00110104
-#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b8644
-#define CONFIG_SYS_DDR_TIMING_2_800 0x0FA888CF
-#define CONFIG_SYS_DDR_CLK_CTRL_800 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_800 0x00441420
-#define CONFIG_SYS_DDR_MODE_2_800 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_800 0x0C300100
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_800 0x8675f608
-
-/* settings for DDR3 at 667MT/s */
-#define CONFIG_SYS_DDR_TIMING_3_667 0x00010000
-#define CONFIG_SYS_DDR_TIMING_0_667 0x00110004
-#define CONFIG_SYS_DDR_TIMING_1_667 0x5d59e544
-#define CONFIG_SYS_DDR_TIMING_2_667 0x0FA890CD
-#define CONFIG_SYS_DDR_CLK_CTRL_667 0x03000000
-#define CONFIG_SYS_DDR_MODE_1_667 0x00441210
-#define CONFIG_SYS_DDR_MODE_2_667 0x00000000
-#define CONFIG_SYS_DDR_INTERVAL_667 0x0a280000
-#define CONFIG_SYS_DDR_WRLVL_CONTROL_667 0x8675F608
-
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* NOR Flash on IFC */
#define CONFIG_SYS_FLASH_BASE 0xee000000
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_NOR_FTIM3 0x0
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
/* CFI for NOR Flash */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE 0xff800000
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
#if defined(CONFIG_TARGET_P1010RDB_PA)
/* NAND Flash Timing Params */
FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS3_FTIM3 0x0
-#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \
- defined(CONFIG_RAMBOOT_NAND)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* Config the L2 Cache as L2 SRAM
#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xD0001000
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (128 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 96 * 1024)
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE 0xD0001000
-#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024)
-#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10)
-#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024)
#else
#define CONFIG_SYS_INIT_L2_ADDR 0xD0000000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x3000)
-#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
#endif
#endif
#endif
/* I2C EEPROM */
#if defined(CONFIG_TARGET_P1010RDB_PB)
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define MAX_NUM_PORTS 9 /* for 128Bytes EEPROM */
#endif
/* enable read and write access to EEPROM */
#endif /* CONFIG_TSEC_ENET */
-/* SATA */
-#define CONFIG_FSL_SATA_V2
-
-#ifdef CONFIG_FSL_SATA
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
-#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
-
-#define CONFIG_LBA48
-#endif /* #ifdef CONFIG_FSL_SATA */
-
#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#endif
-
-#define CONFIG_HAS_FSL_DR_USB
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
+#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
#endif
/*
* Environment
*/
-#if defined(CONFIG_SDCARD)
-#define CONFIG_FSL_FIXED_MMC_LOCATION
-#elif defined(CONFIG_MTD_RAW_NAND)
+#if defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define SPL_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
-#else
-#if defined(CONFIG_TARGET_P1010RDB_PA)
-#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) /* 3*16=48K for env */
-#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_ENV_RANGE (32 * CONFIG_ENV_SIZE) /* new block size 512K */
-#endif
#endif
#endif
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
|| defined(CONFIG_FSL_SATA)
#endif
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* Environment Configuration
projects / platform / kernel / u-boot.git / blobdiff