configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFS

[platform/kernel/u-boot.git] / include / configs / P1010RDB.h

diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index cd9cd9a..a249fa6 100644 (file)
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -130,8 +130,6 @@
 #endif
 
 /* High Level Configuration Options */
-#define CONFIG_FSL_IFC                 /* Enable IFC Support */
-#define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
 #define CONFIG_SYS_HAS_SERDES          /* common SERDES init code */
 
 #if defined(CONFIG_PCI)
@@ -193,7 +191,6 @@
 #endif
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif
 
 #define CONFIG_TSEC_ENET
@@ -305,9 +302,6 @@ extern unsigned long get_sdram_size(void);
  * IFC Definitions
  */
 /* NOR Flash on IFC */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_NO_FLASH
-#endif
 
 #define CONFIG_SYS_FLASH_BASE          0xee000000
 #define CONFIG_SYS_MAX_FLASH_SECT      256     /* 32M */
@@ -360,7 +354,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITION
-#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT                 "nand0=ff800000.flash"
 #define MTDPARTS_DEFAULT               \
        "mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
@@ -504,7 +497,6 @@ extern unsigned long get_sdram_size(void);
 #endif
 #endif
 
-#define CONFIG_BOARD_EARLY_INIT_F      /* Call board_pre_init */
 #define CONFIG_BOARD_EARLY_INIT_R
 
 #define CONFIG_SYS_INIT_RAM_LOCK
@@ -596,7 +588,6 @@ extern unsigned long get_sdram_size(void);
 #define MAX_NUM_PORTS                  9 /* for 128Bytes EEPROM */
 #endif
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -665,23 +656,18 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_SATA2               CONFIG_SYS_MPC85xx_SATA2_ADDR
 #define CONFIG_SYS_SATA2_FLAGS         FLAGS_DMA
 
-#define CONFIG_CMD_SATA
 #define CONFIG_LBA48
 #endif /* #ifdef CONFIG_FSL_SATA  */
 
 #ifdef CONFIG_MMC
-#define CONFIG_DOS_PARTITION
 #define CONFIG_FSL_ESDHC
-#define CONFIG_GENERIC_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #endif
 
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #endif
@@ -736,22 +722,12 @@ extern unsigned long get_sdram_size(void);
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
                 || defined(CONFIG_FSL_SATA)
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
 #endif
 
 /*
@@ -803,8 +779,6 @@ extern unsigned long get_sdram_size(void);
 
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE                115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
        "hwconfig=" __stringify(CONFIG_DEF_HWCONFIG)  "\0"      \
        "netdev=eth0\0"                                         \