#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
-#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1010 RDB */
#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */
#define CONFIG_HWCONFIG
/* DDR Setup */
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
| CSOR_NAND_PB(128)) /*Pages Per Block = 128 */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
/*
* Config the L2 Cache as L2 SRAM
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=" __stringify(CONFIG_DEF_HWCONFIG) "\0" \
"netdev=eth0\0" \
"i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
#endif
-#define CONFIG_RAMBOOTCOMMAND \
+#define RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs; " \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#define CONFIG_BOOTCOMMAND RAMBOOTCOMMAND
#include <asm/fsl_secure_boot.h>