#include <linux/stringify.h>
#include <asm/config_mpc85xx.h>
-#define CONFIG_NAND_FSL_IFC
#ifdef CONFIG_SDCARD
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
#else
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_NAND_INIT
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SPL_MAX_SIZE (128 << 10)
-#define CONFIG_TPL_TEXT_BASE 0xD0001000
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10)
#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_NAND_MINIMAL
#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0xD0000000
#define CONFIG_SYS_NAND_U_BOOT_START 0xD0000000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10)
#endif
#define CONFIG_SPL_PAD_TO 0x20000
#define CONFIG_TPL_PAD_TO 0x20000
#endif
#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_TPL_TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE 0xD0001000
#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#endif
/* High Level Configuration Options */
-#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
#if defined(CONFIG_PCI)
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
/*
* PCI Windows
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
-#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */
-
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 1
/* DDR3 Controller Settings */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
| CSOR_NAND_PB(128)) /*Pages Per Block = 128 */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#undef CONFIG_SYS_RAMBOOT
#endif
-#ifdef CONFIG_SYS_FSL_ERRATUM_IFC_A003399
-#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_A003399_NOR_WORKAROUND
-#endif
-#endif
-
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* End of used area in RAM */
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
-#define CONFIG_ETHPRIME "eTSEC1"
-
/* TBI PHY configuration for SGMII mode */
#define CONFIG_TSEC_TBICR_SETTINGS ( \
TBICR_PHY_RESET \
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#if defined(CONFIG_HAS_FSL_DR_USB)
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
#endif
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
|| defined(CONFIG_FSL_SATA)
#endif
* Environment Configuration
*/
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
#define CONFIG_EXTRA_ENV_SETTINGS \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- CONFIG_BOOTMODE
+ BOOTMODE
#if defined(CONFIG_TARGET_P1010RDB_PA)
-#define CONFIG_BOOTMODE \
+#define BOOTMODE \
"boot_bank0=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
"mw.b ffb00011 0; mw.b ffb00009 0; reset\0" \
"boot_bank1=i2c dev 0; i2c mw 18 1 f1; i2c mw 18 3 f0;" \
"mw.b ffb00011 0; mw.b ffb00017 1; reset\0"
#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_BOOTMODE \
+#define BOOTMODE \
"boot_bank0=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
"i2c mw 19 1 2; i2c mw 19 3 e1; reset\0" \
"boot_bank1=i2c dev 0; i2c mw 18 1 fe; i2c mw 18 3 0;" \
"i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
#endif
-#define RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND RAMBOOTCOMMAND
-
#include <asm/fsl_secure_boot.h>
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff